Washer Dryer Combo Valves

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334310

Manufacturer Part Number

279834

This OEM kit comes with two ignition coils (one three-terminal boost/hold coil, and one two-terminal secondary coil). Usually only one of them burns out, but you should replace them as a set as both have to be operational for the gas valve to open. The primary purpose of the part is to open the gas valve and allow the gas to enter the burner. This is a safety mechanism to make sure that there is never an unsafe buildup of gas inside the appliance. You will find the coils attached to the dryer gas valve. This is not an uncommon repair; it can fail due to normal material fatigue over time. To test your current parts, watch the burner, and if the igniter glows for a while and then shuts off without the gas is igniting, it usually means one of these coils is bad.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX3527427

Manufacturer Part Number

5220FR2006H

The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with water at all. If this happens the valve should be replaced. There are a couple different methods for testing if your hot water valve is defective. The first is to use a multimeter on the solenoid, the second is to unplug the washer while it is running. If water continues to flow into the machine, then the valve is defective. This genuine OEM part has a standard hose fitting inlet, one water outlet, and measure approximately 3 inches long by 3 inches wide. To complete this repair, you will need to disconnect the water and power supply to your washer and pull it out from the wall so you can access the back panel.

★★★★★

★★★★★

1 Review

Fix Number

FIX12374721

Manufacturer Part Number

AJU75152601

This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.

Fix Number

FIX11728995

Manufacturer Part Number

5220FR2075L

If your washing machine is leaking, slow to fill, will not stop filling with water, or is not filling at all, the cold-water inlet valve may be defective. The purpose of the valve is to open to allow water into the washer, and is used for cold water, liquid bleach, and prewash cycles in your washing machine. This is a genuine OEM replacement part that measures approximately 4 inches long and 3 inches wide. It has a standard hose fitting inlet along with two outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left. When replacing this part, you will want to disconnect the power and water to your washer and remove the fill hoses. You will need to pull the machine out far enough so that you are able to access the back panel where the valves are located.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334646

Manufacturer Part Number

285805

There are many symptoms that may indicate an issue with your water inlet valve. These can include your washer not filling with water, it will not stop filling, the washer is leaking, or it is both filling and draining at the same time. You can test if your valve is faulty two different ways. The first is to disconnect the power while the washer fills, if water continues to fill the tub, then the valve should be replaced. The second way is to use a multimeter to test for continuity on the valve solenoids. If you do need to replace the water inlet valve, this is a genuine OEM part that has two ports and is compatible with half-inch ID hose. Before beginning your repair, please be sure to disconnect the power and water supply to your washing machine.

Fix Number

FIX3527452

Manufacturer Part Number

5221ER1003A

This water inlet valve controls cold water flow for the bleach dispenser and prewash cycles. It has one standard hose inlet and three angled outlets—two to the right, one to the left. Designed for select washing machines, it ensures proper water distribution. Disconnect power and water before installation.

Fix Number

FIX1583805

Manufacturer Part Number

205613

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

Fix Number

FIX12587936

Manufacturer Part Number

5221ER1003S

This inlet valve assembly controls the flow of hot and cold water into the washing machine, ensuring proper pressure and volume for each cycle. Made from durable, rust-resistant materials, it’s a reliable replacement for worn or leaking valves. Designed for select LG models, it helps restore efficient water control and washing performance.

Fix Number

FIX11750469

Manufacturer Part Number

WPW10212596

Water inlet valve controls the water flow into the washer. Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW and YNFW; and Inglis IFW and YIFW. Also fits some laundry centers in these series: Whirlpool CET and CGT; and Maytag MLE and MLG.

Fix Number

FIX16221394

Manufacturer Part Number

5304524455