OEM Uni Washer Dryer Combo Parts | Expert DIY Repair Help & Fast Shipping | Fix.com

Popular Uni Washer Dryer Combo Parts

$10.28
Multi-Rib Drum Belt
Fix Number FIX3408299
Manufacturer Part Number 137292700
This belt helps rotate from the drive motor to the drum.
Fixes these symptoms
Noisy
Will Not Start
Will not tumble

See more...
Installation Instructions
michael from Cave City, KY says,

browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple...read more

$38.93
Door Catch
Fix Number FIX418433
Manufacturer Part Number 131658800
This part helps keep the door closed while the machine is running.
Fixes these symptoms
Door won’t close
Will Not Start


Installation Instructions
Steve from Little Falls, MN says,

Broken door catch
Grab it with a pliers, jerk it out of the hole. Insert the new one. Easy Peasy, lemon squezy....read more

$15.81
Drive V-Belt
Fix Number FIX1146950
Manufacturer Part Number 134511600
This washer drive belt connects to the drive motor to activate the system in the washer and spin the basket. If your belt is broken, then the washer might not spin, if this is the case, then it is best to replace this part. Refer to the diagram provided by the manufacturer for installation instructions.
Fixes these symptoms
Burning smell
Noisy
Pumps but will not spin

See more...
Installation Instructions
michael from Cave City, KY says,

browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple...read more

$11.04
Thermal Limiter - Limit 220
Fix Number FIX419402
Manufacturer Part Number 134120900
This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.
Fixes these symptoms
No heat or not enough heat
Shuts off too soon
Takes too long to dry

See more...
Installation Instructions
George B. from Ringgold, GA says,

dryer would not dry anything. The heating unit would not stay on.
First unplug the unit from the power source. You must disassemble the dryer to get to the cycling thermostat. Using a Philips screwdriver, remove the panel below the dryer, then you must remove the ...read more

$4.75
Drum Support Bearing
Fix Number FIX418807
Manufacturer Part Number 131825900
This is a drum support bearing for your dryer. This part attaches to the inside of the rear panel of the cabinet. The drum support bearing helps rotate the drum smoothly and quietly. If your dryer is noisy and will not tumble, you will need to replace this part. Note that this is a drum bearing only.
Fixes these symptoms
Marks left on clothes
Noisy
Will Not Start

See more...
Installation Instructions
michael from Cave City, KY says,

browning clothes .zipper on jackets were tore off
after watching video and reading the review, whole job was simple...read more

$25.12
Drum Glide - White
Fix Number FIX5574052
Manufacturer Part Number 137513300
Appliance requires 2 .Sold individually. This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.
Fixes these symptoms
Marks left on clothes
Noisy
Will not tumble

See more...
Installation Instructions
Robert from Derry, NH says,

Squeezing, clothes getting stuck.
This is a stacking washer & dryer. The best advice I read was to remove the door. It made the front panel much easier to remove. Removing the upper and lower felt was very easy. I used a sharp chisel ...read more

$33.00
Dryer Lint Screen
Fix Number FIX12585473
Manufacturer Part Number 5304516871
This dryer lint screen (part number 5304516871) is for laundry centers. Dryer lint screen 5304516871 captures lint and debris from the exhaust air flowing from the dryer. Follow the instructions in the owner's manual when installing this part.
Fixes these symptoms
Door won’t close
Takes too long to dry


Installation Instructions
Jacquelyn from Suisun City, CA says,

The wire screen on the lint filter was all bent out of shape and it would not sit properly in the space.and prevented the door from closing.
I lifted out the old lint filter and dropped the new one in the space provided. What a concept, NO TOOLS REQUIRED! It fit perfectly, thanks for the quick delivery....read more

$10.02
Door Strike
Fix Number FIX455020
Manufacturer Part Number 5303207102
"Male" piece of a dryer door closing mechanism.
Fixes these symptoms
Door won’t close


$17.03
Lower Front Felt Seal with Adhesive
Fix Number FIX832645
Manufacturer Part Number 5303937183
Fixes these symptoms
Marks left on clothes
Noisy
Takes too long to dry

See more...
Installation Instructions
Robert from Derry, NH says,

Squeezing, clothes getting stuck.
This is a stacking washer & dryer. The best advice I read was to remove the door. It made the front panel much easier to remove. Removing the upper and lower felt was very easy. I used a sharp chisel ...read more

$111.73
Drain Pump - 120V 60 Hz.
Fix Number FIX7783938
Manufacturer Part Number 137221600
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
Fixes these symptoms
Leaking
Noisy
Not draining

See more...
Installation Instructions
matthew from varysburg, NY says,

No drain, no spin cycle.
Remove the top panel, control panel, remove the seal ring, the door switch, and then the front panel. Unhook to green hose clamps. Shop vac old water, remove the burned up drain motor by 2 mount...read more

Popular Uni Washer Dryer Combo Models