Uni Parts

Light Bulb Clear, 120 Volt, 40 Watt.

Oven Bake Element

★★★★★

★★★★★

(10)

This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.

Drip Bowl - 8"

★★★★★

★★★★★

(1)

This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic. While the replacement may be visually different from the original, it will fit your appliance. If your drip bowl has become discolored, corroded, or otherwise damaged, it needs to be replaced. This drip bowl is sold individually, so if you would like to replace all 4 drip bowls on your appliance you will need to account for this. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.

Defrost Timer - 60Hz 120V If your freezer will not defrost, or your fridge and freezer are too warm, there may be an issue with the defrost timer. This device helps to melt ice that builds up on the evaporator coils. It does this by cycling on the heater circuit for thirty minutes after every eight hours that the compressor has been running. There is also a dial on the timer that can be advanced in and out of defrost mode if you need to adjust things manually. If frost is allowed to build up, it can reduce airflow and the efficiency of your appliance. If you need to replace the defrost timer, this is an authentic OEM part. It measures approximately 3 inches long and 2.5 inches wide, with 60Hz and 120V. Please be sure to disconnect the power supply to your fridge before beginning this repair.

Terminal Block Kit This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and wires. The purpose of this part is to connect the wire harness to the surface element, which allows for the burners to heat up. Some common issues that result from a damaged terminal block is that your element will not heat properly or not heat up at all, may cause burning smell, or make a buzzing noise. If you remove the element and the tips are black, that is a good sign there is a problem with the terminal block and it should be replaced. It may also be necessary to replace the burner elements as well, if the tips are badly damaged. This repair will require a pair of wire strippers, a #1 square head screwdriver, and a heat gun or hair dryer. If you are not comfortable with cutting, stripping, and reconnecting of wires you should contact a qualified professional to complete this repair. Please be sure to disconnect the power supply to your appliance before starting this repair. As this is a genuine OEM parts kit, it will be compatible with your appliance model.

Chrome Drip Bowl - 6"

★★★★★

★★★★★

(2)

This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits under 6-inch burner elements and has a diameter of approximately 8-inches. While the replacement may be visually different from the original, if you have used your correct model number to search, this will fit your appliance. Common reasons to replace this often neglected part is if it has become discolored, corroded, or otherwise damaged. Each drip bowl is sold individually. This is a good time to inspect all drip bowls on the appliance, if you would like to give your appliance a fresh look, keeping in mind that they may be different sizes and are sold separately. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.

Dishwasher Bottom Door Gasket

★★★★★

★★★★★

(3)

This dishwasher door gasket is attached to the bottom of the door, creating a strong seal between the tub and the outer edge of the door. This seal is prone to wear and tear due to its constant exposure to water, detergent, and food particles. If the gasket appears cracked, broken, or you notice a leak coming from the door, it will need to be replaced immediately. This gasket measures approximately 23 inches long. For this simple repair, no tools are necessary. Open the dishwasher door and remove the bottom rack. The gasket is located right along the bottom of the door, molded inside the channel. It is held in place in the groove across the bottom. Remove the old gasket by pulling it out with your hands. Take your new silicone gasket and line it up so the notch fits into the groove and slide it in place until it is secure. Reinstall the lower dishrack. We recommend leaving the door closed for a few hours to ensure the gasket is sealed tightly.

Lower Spray Arm

★★★★★

★★★★★

(4)

This is a single lower spray arm found in dishwashers to spray water and detergent vigorously over the dishes. This spray arm is made of plastic, so can warp or crack with time. The holes in the spray arm can get clogged with debris, so it should be cleaned every so often. If it is beyond cleaning or damaged, it will need to be replaced. If the holes are clogged, this can sometimes mean there is a problem with the filter system, so it is a good idea to inspect this as well. For this repair, start by turning off the water supply to the dishwasher. Pull the lower rack out of the dishwasher and out of the way. Remove the lower wash arm. Using a flathead screwdriver, push the small locking tabs located on each side at the bottom of the spray arm. You should now be able to easily pull the spray arm out of the dishwasher. Align the new lower wash arm and push it down to secure it in place. Make sure it can spin freely and is not making contact with the heating element. Place the lower dishrack back into the appliance and close the door.

Freezer Door Key

★★★★★

★★★★★

(1)

This is a genuine OEM replacement key for the door of upright or chest freezers. If you have misplaced or damaged your key, you will need a replacement in order to lock and unlock your freezer door. We recommend storing the key in a safe place away from the freezer itself. We recommend testing the new key with the freezer door open, to ensure that the latch opens and closes properly. This key is made from white plastic and is sold individually.

Evaporator Fan Blade