Washer Dryer Combo Belts

★★★★★

★★★★★

18 Reviews

Fix Number

FIX346995

Manufacturer Part Number

341241

This multi rib belt is an OEM replacement part for a dryer. It attaches to the drum, idler pulley, and motor pulley, and is responsible for spinning the drum. Over time, the belt can become frayed, brittle, and inflexible. If you can hear the motor running, but the drum does not turn, it is likely that the belt is broken. Other symptoms of a broken multi rib belt include unusual noises, failing to start, no heat, a burning smell, and an unresponsive touchpad. Depending on the model, you will find the belt by looking behind the front panel or under the main top of the dryer. This belt is 1/4-inches wide, has a length of 92-1/4-inches, and has four ridges and three groves on the belt. Each belt is sold separately.

★★★★★

★★★★★

5 Reviews

Fix Number

FIX373088

Manufacturer Part Number

4392067

This dryer repair kit consists of five commonly replaced dryer parts: one multi-rib belt (part #661570V and measures 93 1/2 inches long), four drum support rollers, one idler assembly, nine tri-rings, and one washer. This universal maintenance kit is an all-encompassing kit for fixing a noisy dryer, among other symptoms, but noisy being the most common. It is compatible with 27-inch wide dryers built from 1965 onwards. Be sure to disconnect the dryer or shut off the house circuit breaker for the appliance before you begin your repair. To access these parts, you will need to remove the dryer drum. For this installation you will need a 1/4-inch nut driver, a long flat-blade screwdriver, a short flat-blade screw diver, and a Phillips screwdriver.

Fix Number

FIX1148434

Manufacturer Part Number

134503600

The drum belt, also known as a drive belt, is a rubber piece that wraps around the dryer drum, idler pulley, and motor pulley and is used to make the drum rotate. If you can hear the motor running, but the drum is not spinning, it may be an issue with the drum belt. Since it is made of rubber, it can become brittle with age causing it to break. Alternatively, it could be stretched out and no longer gripping to the dryer drum. Both of these issues would require you to replace the belt. To do this repair you will need a putty knife to pop open the top and front panel of your dryer, and a Phillip head screwdriver. Be sure to disconnect the power to your appliance before beginning your repair. This drum belt measures 88 and 3/4 inches long by 1/4 inch wide. As it is a genuine OEM part, this size will be compatible with your appliance model.

★★★★★

★★★★★

9 Reviews

Fix Number

FIX11757542

Manufacturer Part Number

WPY312959

This is a single OEM dryer drum belt. It measures 100 inches in length, 3/8 of an inch wide and has five ribs and four grooves. Keep in mind that this rubber drum belt will stretch over time, so if you are comparing your current belt to these specified measurements, they may not be exact. For this repair, you will need to disconnect the power, and remove the front panel and drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver. While you are doing this repair, be careful not to let the belt fall into the groove in the drum, causing it to be too loose.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX11741110

Manufacturer Part Number

WP33002535

If your dryer is noisy while operating, or will not tumble at all, there may be an issue with the drum belt. Over time, the rubber can become brittle and snap, and the belt will need to be replaced. This genuine OEM multi rib dryer drum belt measures approximately 91 and 5/8-inch in length and is 3/8-inch wide. It is made of black rubber and have five ridges, helping it to grip to your dryer drum.

★★★★★

★★★★★

1 Review

Fix Number

FIX2005284

Manufacturer Part Number

12112425

Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the tub. If this happens, the belts will need to be replaced. This OEM belt kit includes the drive belt and the pump belt, which are both V-shaped, and made of black rubber. The pump belt is located between the motor and pump under the washer, and the drive belt is looped around the drive and motor pulley at the bottom of the machine. This repair is easiest to complete if the washer is placed on its back, and you will need to disconnect the power and water supply.

Fix Number

FIX3408299

Manufacturer Part Number

137292700

This belt helps rotate from the drive motor to the drum.

Fix Number

FIX11705916

Manufacturer Part Number

4400EL2001F

If the drum in your dryer will not tumble, or it is noisy while operating, there may be an issue with the drum belt. The belt is found looped around the dryer drum, a tension pulley, and a motor pulley and is used to rotate the drum so that your laundry tumbles. Over time the belt can become stretched out, or it becomes brittle and will snap. If this happens the belt will need to be replaced. If you need a replacement, this is a genuine OEM dryer drum belt. The belt measures about a quarter inch wide, and has four ribs and three groves. Please be sure to disconnect the power supply to your dryer before beginning this repair.

★★★★★

★★★★★

1 Review

Fix Number

FIX11747978

Manufacturer Part Number

WPW10006384

The drive belt works with the pulley in your washer in order to spin the tub. If you notice a burning rubber smell, your washer has become excessively noisy, or it will not spin, it could indicate an issue with the drive belt. Over time the belt can become worn and snap, or it can become loose and no longer provide the proper grip to spin. This is a genuine OEM part for your washer that is black in color and made of rubber.

Fix Number

FIX11722115

Manufacturer Part Number

661570V

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide. This drive belt is 93 1/2 inches long, and 1/4 of an inch wide, with 4 ribs and 3 grooves. To complete this repair, you will need a Phillips screw driver, a 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Make sure to disconnect power to the dryer before beginning this repair.