Amana Washer Dryer Combo Parts

Fix Number

FIX382430

Manufacturer Part Number

661570

This is a single dryer drum belt that measures 93.5 inches. The belt rotates the dryer drum and is a common wear part that can become brittle over time. It can also stretch and change shape, so keep this in mind when comparing your old part to this new replacement part. When this part wears it can cause a thumping noise in your dryer, and that is a typical sign that it needs to be replaced. To access this part, you will need to remove the front panel of your dryer, and the belt will be found looped around the drummer, under the idler pulley wheel, and around the drive pulley. For a successful repair, you will need a pair of needle nose pliers, a Phillips screwdriver, a 1/4-inch nut driver, and a putty knife. Do not forget to disconnect the power to your appliance before you begin.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334244

Manufacturer Part Number

279640

Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin. It is located on the dryer drum, around the tension pulley. If your appliance is noisy during operation, will not tumble, or will not start, you may need to replace this part. It is made of durable plastic and has a diameter of roughly 2-inches. This part also includes the hardware needed for replacement. Most of our customers found this repair to be medium difficulty, and required a Philips screwdriver, 1/4-inch nut driver, putty knife, small flat blade screwdriver, and needle nose pliers to get the job done.

★★★★★

★★★★★

1 Review

Fix Number

FIX11743811

Manufacturer Part Number

WP697772

The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334278

Manufacturer Part Number

279769

This genuine OEM kit includes a high limit thermostat and a thermal cut-off fuse for your dryer. The thermostat has a limit of 250 degrees Fahrenheit, and the fuse has a limit of 360 degrees Fahrenheit. The purpose of these parts is to prevent your dryer from overheating. If your clothes are coming out of the dryer too hot, or there is no heat at all, it is likely that these parts will need to be replaced. To complete this repair, you will need a putty knife, quarter-inch nut driver, and a pair of pliers. Please be sure to disconnect the power supply to your dryer before beginning this repair. The thermostats are located on the element housing, and we find it easiest to remove the entire heating assembly from the dryer in order to replace these parts. Take note when removing the old thermostats, if there is any discoloration on the terminals then the wire ends may also need to be replaced.

★★★★★

★★★★★

1 Review

Fix Number

FIX970088

Manufacturer Part Number

280114

This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.

Fix Number

FIX334206

Manufacturer Part Number

279457

This heating element connection wire kit is a genuine OEM replacement for your electric dryer. The kit is used to connect the thermostat to the heater element. The kit comes with a yellow wire nut and a wire that measures approximately 5 inches in length. If your dryer is getting little to no heat, or is taking too long to dry, you may need to replace this connection wire. Please be sure to disconnect the power supply to your dryer before replacing this part.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334641

Manufacturer Part Number

285785

This is a genuine OEM replacement clutch assembly for your washing machine. A clutch assembly, also known as a clutch or a washer clutch, is responsible for spinning the tub during the spin cycle. If the clutch becomes worn and is no longer operating properly, your clothes will remain soaked after the cycle is finished. Some other signs it is time to replace the clutch is if your washer is noisy while running, there is a burning smell, or the machine is shaking excessively. This kit comes with the clutch, brake cam driver, spring, retaining ring, and a nylon anti-rattle clip. Before beginning this repair, be sure to disconnect the power and water supply to your machine. Depending on your washer model, you may need an additional person to help lower the machine onto its back, as access to the drive shaft to change the clutch assembly may be easiest through the bottom of the appliance.

Fix Number

FIX11751118

Manufacturer Part Number

WPW10250667

This tub spring is a genuine OEM replacement part for your washing machine and is sold individually. There are other names that the tub spring goes by, such as the suspension spring, balance spring, or counterweight spring. The purpose of this spring is to ensure that the tub sits straight during the spin cycle, and it does this by counterbalancing the weight of the motor. If the spring has broken, it will cause the tub to be off-balance, which can make the washer shake and become noisy when spinning. An off-balance tub can also cause damage to other components of your washer, so it should be fixed quickly. If your model of washing machine has more than one tub spring, they should all be replaced at the same time as they tend to wear evenly. The tools you will need to complete this repair are a pair of pliers, a Philips screwdriver, and a flat blade screwdriver. Please be sure to disconnect the power supply to your washer before beginning this repair.

★★★★★

★★★★★

7 Reviews

Fix Number

FIX1485646

Manufacturer Part Number

285753A

This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for added strength. It is located between the motor and transmission on direct drive washers with no belt. If the drive system seizes, the coupling is designed to break to prevent the drive motor from damage. Consequently, this part may need to be replaced as your appliance ages. Never overload your washer, as this can speed up its deterioration. Symptoms of a faulty motor coupling include a washer pumping but not spinning, slow spinning, the washer not agitating, and unusual noises. This coupling kit contains all the parts necessary to replace your existing direct drive motor coupling. Please note, that after replacing the motor coupling your washer may smell like burning rubber for the first few uses, this is entirely normal as the part becomes acclimated to the machine. Each is sold individually.

Fix Number

FIX11752609

Manufacturer Part Number

WPW10314173