Tappan Washer Dryer Combo Parts

Fix Number

FIX470049

Manufacturer Part Number

5303931775

This coil ignition kit is used in dryers to open the gas valve when the dryer is on. This kit includes two coils. One is a two-wire secondary coil and the other is a three-wire booster coil. If your dryer does not heat or you notice heating inconsistencies, then the gas valve may be damaged and it is best to replace it to solve this problem. To repair, first release the two retaining clips that hold the top panel in place, then remove two screws that retain the front panel of the dryer cabinet. Next, pull the front panel forward and remember to disconnect the door switch. After accessing the gas coils, start removing the wires and unscrew the bracket that holds the coils. Remember to remove both the dual and main coil without removing the spacer. For more information on the kit and repair instructions, refer to diagram for a list of the parts.

Fix Number

FIX455020

Manufacturer Part Number

5303207102

"Male" piece of a dryer door closing mechanism.

Fix Number

FIX3408299

Manufacturer Part Number

137292700

This belt helps rotate from the drive motor to the drum.

Fix Number

FIX459818

Manufacturer Part Number

5303281135

This part senses the flame for heat allowing the gas valve to open.

Fix Number

FIX446428

Manufacturer Part Number

3204267

The two-terminal high limit thermostat has a limit of 260 degrees Fahrenheit and acts as a safety mechanism that keeps the dryer from overheating. The thermostat will cut out when the internal dryer temperature reaches 260 and then cuts back in when the temperature drops by 70 degrees Fahrenheit. If your dryer is not heating, you may need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Fix Number

FIX418433

Manufacturer Part Number

131658800

This door catch is an authentic OEM replacement part for your dryer. This part holds the door strike and ensures that the door stays closed while your dryer is running. This prevents hot air or laundry from escaping from the dryer. If your dryer will not start or the door will not stay closed, you may need to replace the door catch. Please be sure to disconnect the power supply to your dryer before beginning this repair.

Fix Number

FIX419402

Manufacturer Part Number

134120900

This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.

Fix Number

FIX460194

Manufacturer Part Number

5303283286

This part helps to keep the dryer running as quietly as possible.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX1146950

Manufacturer Part Number

134511600

If your washer drum is not spinning, there may be an issue with your drive belt. The drive belt wraps around the motor pulley and helps the basket to spin. Other signs there are issues with the belt is if there is a burning rubber smell, or the washer is noisy while spinning. The belt is subjected to wear and tear, and over time it may wear out. This is a genuine OEM part that is made of rubber.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX459829

Manufacturer Part Number

5303281153

This ball-and-socket style bearing kit is used in your dryer to support the rear of the drum as it tumbles through the dry cycle. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time, the bearing or the bushing can wear out, and the ball support can become damaged. If these things happen, your dryer may not tumble, or it will be noisy while operating. If this is the case, you may need to replace these parts. This genuine OEM parts kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high-temperature lubricant, and the installation screws. Completing this repair requires taking the entire drum out of your dryer along with handling greasy parts, so have a rag handy for cleanup. Please ensure that you disconnect the power supply to your appliance before beginning this repair.