Tappan Parts

★★★★★

★★★★★

4 Reviews

Fix Number

FIX12585623

Manufacturer Part Number

5304517203

This is a single lower spray arm found in dishwashers to spray water and detergent vigorously over the dishes. This spray arm is made of plastic, so can warp or crack with time. The holes in the spray arm can get clogged with debris, so it should be cleaned every so often. If it is beyond cleaning or damaged, it will need to be replaced. If the holes are clogged, this can sometimes mean there is a problem with the filter system, so it is a good idea to inspect this as well. For this repair, start by turning off the water supply to the dishwasher. Pull the lower rack out of the dishwasher and out of the way. Remove the lower wash arm. Using a flathead screwdriver, push the small locking tabs located on each side at the bottom of the spray arm. You should now be able to easily pull the spray arm out of the dishwasher. Align the new lower wash arm and push it down to secure it in place. Make sure it can spin freely and is not making contact with the heating element. Place the lower dishrack back into the appliance and close the door.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX438018

Manufacturer Part Number

316075103

This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.

★★★★★

★★★★★

1 Review

Fix Number

FIX437595

Manufacturer Part Number

316048413

This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic. While the replacement may be visually different from the original, it will fit your appliance. If your drip bowl has become discolored, corroded, or otherwise damaged, it needs to be replaced. This drip bowl is sold individually, so if you would like to replace all 4 drip bowls on your appliance you will need to account for this. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.

Fix Number

FIX16745479

Manufacturer Part Number

5304532229

This is a single rack roller kit for your dishwasher. This kit comes with one axel/clip, and one wheel/roller. The kit is used for the lower dishrack, and allows your rack to move freely. You will need two kits for your upper and lower rack. We recommend replacing this part in pairs for an even wear. Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX1145040

Manufacturer Part Number

316436001

The infinite burner switch is used to control the temperature of the burner element on your stove top. This model is for the larger, eight-inch element. If your burner is not heating up or has uneven temperatures, you should first check with a multimeter to see if the issue is with the element or with the infinite burner switch. If you need to replace the switch, first disconnect the power supply to your range. To change this part, you will need access to the back panel, so you will need to pull the appliance out from the wall. To complete the repair, you will need a pair of needle nose pliers, a number one square head screwdriver, and a Philips screwdriver. The specifications for this genuine OEM part are that the switch is 240-volt, 2100-2600 watt, and 8.8-10.8 amp.

★★★★★

★★★★★

5 Reviews

Fix Number

FIX12364147

Manufacturer Part Number

241798231

This is a genuine OEM ice maker assembly for your refrigerator. The ice maker makes eight cubes at a time, by filling the mold with water from the inlet valve, freezing the water until the cubes are formed, and then ejecting them into the storage bucket. This process will repeat until the ice bucket is full. If your device is not making ice cubes, the ice maker assembly may need to be replaced. Please ensure that you disconnect the power and water supply to your fridge before beginning this repair. This kit includes the fill cup, a four-pin wire harness adapter, and tube.

Fix Number

FIX1148434

Manufacturer Part Number

134503600

The drum belt, also known as a drive belt, is a rubber piece that wraps around the dryer drum, idler pulley, and motor pulley and is used to make the drum rotate. If you can hear the motor running, but the drum is not spinning, it may be an issue with the drum belt. Since it is made of rubber, it can become brittle with age causing it to break. Alternatively, it could be stretched out and no longer gripping to the dryer drum. Both of these issues would require you to replace the belt. To do this repair you will need a putty knife to pop open the top and front panel of your dryer, and a Phillip head screwdriver. Be sure to disconnect the power to your appliance before beginning your repair. This drum belt measures 88 and 3/4 inches long by 1/4 inch wide. As it is a genuine OEM part, this size will be compatible with your appliance model.

Fix Number

FIX470125

Manufacturer Part Number

5303935058

This kit comes with the necessary components to replace your burner terminal block. It includes interchangeable mounting brackets, a terminal box, ceramic wire nuts, heat shrink protective tubing, and wires. The purpose of this part is to connect the wire harness to the surface element, which allows for the burners to heat up. Some common issues that result from a damaged terminal block is that your element will not heat properly or not heat up at all, may cause burning smell, or make a buzzing noise. If you remove the element and the tips are black, that is a good sign there is a problem with the terminal block and it should be replaced. It may also be necessary to replace the burner elements as well, if the tips are badly damaged. This repair will require a pair of wire strippers, a #1 square head screwdriver, and a heat gun or hair dryer. If you are not comfortable with cutting, stripping, and reconnecting of wires you should contact a qualified professional to complete this repair. Please be sure to disconnect the power supply to your appliance before starting this repair. As this is a genuine OEM parts kit, it will be compatible with your appliance model.

Fix Number

FIX735091

Manufacturer Part Number

240535101

This door rack is for the bottom shelf of your refrigerator door, the top and middle shelf racks are sold separately. Please note that these doors racks are sold individually and not part of a kit. This particular part measures approximately 23 inches wide and is made of white plastic. This is a certified OEM part, which ensures it fits your fridge properly. This part helps to keep small items on the fridge door shelf and should be replaced if it cracks or breaks. Replacing the door rack (also known as a retainer bar) is a simple process and does not require any tools. Pop the old, broken rack out and snap the new one in, making sure that the locking tabs are secure.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX437596

Manufacturer Part Number

316048414

This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits under 6-inch burner elements and has a diameter of approximately 8-inches. While the replacement may be visually different from the original, if you have used your correct model number to search, this will fit your appliance. Common reasons to replace this often neglected part is if it has become discolored, corroded, or otherwise damaged. Each drip bowl is sold individually. This is a good time to inspect all drip bowls on the appliance, if you would like to give your appliance a fresh look, keeping in mind that they may be different sizes and are sold separately. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.