Washer Dryer Combo Wheels and Rollers

Drum Support Roller Kit

★★★★★

★★★★★

9 Reviews

This OEM drum support roller kit contains the parts needed to replace one roller on your dryer. This kit includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once for optimal performance. The drum support roller holds the drum in position while it spins on the support wheels. It rotates on the roller shaft located on the rear bulkhead. It may need to be replaced if your dryer is noisy, will not tumble, leaves marks on clothes, or will not start. This part is prone to wear and tear, and if broken will need to be replaced. This part measures roughly 3 inches in diameter and is made of plastic, metal, and rubber. Each kit is sold individually (two would be needed to replace both drum support rollers, which is recommended).

Dryer Drum Support Roller This drum support roller kit contains the parts needed to replace one roller on your dryer and is an OEM approved replacement part. This kit includes one drum roller and two bearings. Tri-rings are sold separately. The drum support roller holds the drum in position while it spins on the support wheels. Most dryers use two drum rollers, and it is recommended to change both at once to ensure proper drum rotation and even wear. A common symptom of a worn drum support roller is an unusually noisy dryer. This repair has been rated by customers as medium difficulty, and generally takes 30-60 minutes to complete. For your safety, you must disconnect the power, gas, and vent lines before you begin. For this repair you may need a nut driver, pliers, a screwdriver, and a wrench.

Rear Drum Support Roller Kit

★★★★★

★★★★★

3 Reviews

This is a rear drum support roller kit for your dryer. The 2 rollers come with 4 tri-rings, and 1 palnut. We recommend that you replace both rollers at once. This kit stabilizes the drum cylinder, while letting the drum rotate on the support rollers. If you are having problems with your appliance during tumble mode, or if it is too noisy, you will need this kit. To complete this repair you will need a putty knife, Philips screwdriver and a 5/16 nut driver.

Idler Pulley

★★★★★

★★★★★

2 Reviews

Often referred to as a dryer belt tension pulley wheel, this idler pulley is an OEM approved replacement part for a variety of dryer models. The idler pulley puts tension on the drive belt, and if the idler pulley fails to put the proper amount of tension on the belt, the dryer will not spin. It is located on the dryer drum, around the tension pulley. If your appliance is noisy during operation, will not tumble, or will not start, you may need to replace this part. It is made of durable plastic and has a diameter of roughly 2-inches. This part also includes the hardware needed for replacement. Most of our customers found this repair to be medium difficulty, and required a Philips screwdriver, 1/4-inch nut driver, putty knife, small flat blade screwdriver, and needle nose pliers to get the job done.

Blower Wheel with Clamp

★★★★★

★★★★★

2 Reviews

The blower wheel is responsible for blowing heat into the dryer drum, and out of the exhaust vent. If you notice that your dryer is taking too long to dry or is make unusually loud noises, it may be time to replace the blower wheel. This genuine OEM replacement part comes with a metallic clamp that holds the wheel in place. This part attaches to the drive motor shaft and can be accessed by removing the front panel of the dryer. Be sure to disconnect the power supply before beginning this repair.

Drum Roller Shaft - Left Side Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.

Drum Support Shaft - Rear Shaft with Right Hand Threads Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.

Drum Support Roller Shaft - Right Side Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.

Drum Support Roller Shaft - Right Hand Threads This shaft is for the front with right hand thread. Sold individually.

Tension Idler Pulley

★★★★★

★★★★★

1 Review

This idler arm assembly comes with the pulley wheel.