OEM Kenmore Washer Parts | Expert DIY Repair Help & Fast Shipping

$6.04

Touch-Up Paint - White

Fix Number FIX385132

Manufacturer Part Number 72017

18ml

Installation Instructions

Al from Cape Coral, FL

No heat when trying to dry clothes .

Followed instructions on your videos. Everything went as planned and the dryer works like new.... Read more...

$4.24

Agitator Directional Cogs

★★★★★

18 Reviews

Fix Number FIX388034

Manufacturer Part Number 80040

Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.

Fixes these symptoms

Does not dispense fabric softener or detergent
Marks left on clothes
Not cleaning dishes properly
See more...

Installation Instructions

John from La Mesa, CA

Upper agitator stopped working

Followed the simple instructions on youtube, searching for "kenmore upper agitator doesn't work." There are a number of videos there. Find the notch on agitator cover and pry off the cover using a flat screw driver. Remove the nut in the center of the agitator using the 7/16 socket with extension. Remove upper agitator (mine came off easily but some may require removing the entire agitator, then pulling off the upper agitator). Remove assembly from inside and replace the dogs. Reassemble. Read more...

$4.76

Suspension Spring

Fix Number FIX11743345

Manufacturer Part Number WP63907

This suspension spring is a genuine OEM replacement part for a variety of washers and washer-dryer combos. The primary purpose of the suspension spring is to support the outer tub and keep the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. This part is approximately 2 inches in length when compressed, made of durable metal, and is sold individually. For this repair, you will need a 1/4 nut driver, putty knife, flat blade screwdriver, and a pair of needle-nose pliers. Before you begin, disconnect the power, fill hoses, and drain hose to give you easy and safe access (drain hose may release some water, have a small container or towel near by). Your appliance contains 3 suspension springs, so keep this in mind if you need to order multiple of this part. We suggest you purchase several at a time, as they can be very useful to have on-hand.

Fixes these symptoms

Leaking
Shaking and Moving
See more...

Installation Instructions

CARLOS from EL PASO, TX

just to understand the type and different model videos

exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars Read more...

$6.80

Agitator Bolt

Fix Number FIX11741866

Manufacturer Part Number WP358237

This bolt is a genuine OEM replacement part, used to secure the agitator in your washing machine. Overtime the bolt can become worn out due to the vibrations of the washer, and will need to be replaced. The size of the screw head is 7/16 inch, so you will need the appropriately sized socket to complete this repair. The new bolt comes with a rubber gasket and a threaded sealant.

Fixes these symptoms

Leaking
Marks left on clothes
Spins slowly
See more...

Installation Instructions

Jerry from Aransas Pass, TX

Agitator not working correctly and leaking from somewhere underneath.

I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...

$26.92

Direct Drive Motor Coupling

★★★★★

7 Reviews

Fix Number FIX1485646

Manufacturer Part Number 285753A

This is an OEM direct drive motor coupling, which provides a cushioned connection between the transmission and the motor shaft. This is the newer version of this part, made with new metal sleeves for added strength. It is located between the motor and transmission on direct drive washers with no belt. If the drive system seizes, the coupling is designed to break to prevent the drive motor from damage. Consequently, this part may need to be replaced as your appliance ages. Never overload your washer, as this can speed up its deterioration. Symptoms of a faulty motor coupling include a washer pumping but not spinning, slow spinning, the washer not agitating, and unusual noises. This coupling kit contains all the parts necessary to replace your existing direct drive motor coupling. Please note, that after replacing the motor coupling your washer may smell like burning rubber for the first few uses, this is entirely normal as the part becomes acclimated to the machine. Each is sold individually.

Fixes these symptoms

Burning smell
Leaking
Noisy
See more...

Installation Instructions

Joseph from Burnsville, NC

Washer would not spin or agitate

First, I found it very easy to follow the help on your web site to determine the most likely parts that would cause my problems. The direct drive motor coupling could be the cause of both problems. Also the agitator repair kit was the most likely cause of the agitator problem, So, I ordered both parts. When AI received the parts there were videos included instructing every detail for installation. I just followed the video for the direct drive motor coupling and both problems were solved with the one part. It took about 30 minutes and was a simple installation. .Thanks for your good service. It saved me a service call or maybe a new washer and dryer set. Read more...

$5.56

Centerpost Gasket

Fix Number FIX11723081

Manufacturer Part Number W10814296

Also known as Main Outer Tub Seal. This part helps to prevent leaking from the bottom of the tub.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Cathie from Philadelphia, PA

Washer was leaking a little. A very small puddle formed underneath and to the left of the machine.

The installation video was sensational and invaluable. I watched it all the way through and then took it step by step as I repaired the machine. I ordered the water pump and the gasket at the same time, not knowing which part would solve the problem. The water pump was the easiest to replace so I replaced that, put the machine back together--only to discover that the leak prevailed. I disassembled the machine again to replace the gasket. I cued up the video and follwed every step. I didn't have a spanner wrench so I had to wait for it to arrive. No hardware store or bib-box store carries this wrench. The hardest part of the whole job was removing that nut from the agitator. The spanner wrench fit perfectly but despite a lot of pounding combined with a lot of lubricant and dissolvant, it wouldn't budge. After 20 years, that nut was really on there. I went to an automotive store and asked for their best-performing lubricant. They recommended PB Blaster Penetrating Catalyst over any of the others, and wow, were they right! I lined the tub with paper towels for protection, sprayed a lot of PB Blaster on the nut, came back in 15 minutes and that nut came right off. It was unbelievable, and I was ecstatic. From there I relied on the video, took my time, cleaned the tub and everything else (which was filthy with tons of pet hair caked on!) put it all back together, hoped for the best, ran a load and was absolutely thrilled that there was no leaking! A really good project and a lot of money saved. I could never have done it and would not have attempted it without that superb installation video. Read more...

$7.68

Hose Clamp

Fix Number FIX11743008

Manufacturer Part Number WP596669

This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Albert from Unadilla, NY

noticed water was leaking in front of washer-right before we were leaving for vacation

Upon returning from vacation, we needed to do laundry-so I put some plastic under the washer and we did a load. The water was leaking from the seam between the lid and the back panel on the side with the hot and cold water connections- not the front. I removed two screws from the front bottom panel and two screws from the underside of the lid.Turning the washer on showed the leak was coming from the injection valve( it was brittle from age). The rubber injection valve was replaced and installed( using a little liquid soap to help the rubber hose to slip over the rubber injection valve) with a new clamp. The leak was fixed. Read more...

$10.72

Hose Clamp

Fix Number FIX11740613

Manufacturer Part Number WP285655

This hose clamp is sold individually.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Jacob from Center, TX

The drain hose had a hole in it and needed to be replaced

Removed the lower front panel, disconnected the hose and replaced it with the new one, then replace the panel. The most dificult part was getting my old self on the floor and unscrewing the panel nuts. Read more...

$6.80

Tub Spring

Fix Number FIX11751118

Manufacturer Part Number WPW10250667

This tub spring is a genuine OEM replacement part for your washing machine and is sold individually. There are other names that the tub spring goes by, such as the suspension spring, balance spring, or counterweight spring. The purpose of this spring is to ensure that the tub sits straight during the spin cycle, and it does this by counterbalancing the weight of the motor. If the spring has broken, it will cause the tub to be off-balance, which can make the washer shake and become noisy when spinning. An off-balance tub can also cause damage to other components of your washer, so it should be fixed quickly. If your model of washing machine has more than one tub spring, they should all be replaced at the same time as they tend to wear evenly. The tools you will need to complete this repair are a pair of pliers, a Philips screwdriver, and a flat blade screwdriver. Please be sure to disconnect the power supply to your washer before beginning this repair.

Fixes these symptoms

Leaking
See more...

Installation Instructions

CARLOS from EL PASO, TX

just to understand the type and different model videos

exactly as the video mentioned, just need to explain if some models are alike or different using the same part numbers will be awesome.in my case my washer had the screws in different areas to disassemble and Assembly the spare parts, other than that beautiful idea in sending the link video with the email confirmation let me tell you first class and top of the line customer service rated 5 Stars Read more...

$47.10

Direct Drive Water Pump

Fix Number FIX11741239

Manufacturer Part Number WP3363394

The direct drive water pump is used in washing machines that do not have belts, to remove water from the tub during the drain cycle. It is located on the motor and attached by two clips. The drain pump has two ports for water to pass through, one port is larger than the other, and this is where the hoses connect. If your washer leaks, will drain the water, or is filling and draining at the same time, there may be an issue with your pump. Blockages or clogs in the hoses may be contributing to this. Before you replace the pump, be sure to disconnect the power and water lines to your appliance. This repair requires a pair of slip-joint pliers, a flat head screwdriver, and a putty knife. You may find it useful to have a container on hand to collect any water left in the hoses, and to have another person to assist with lifting and lowering the machine. This is a genuine OEM part made of durable white plastic. Other names you may know it by include direct drive washer pump, drain pump, washer drain pump, or water pump.

Fixes these symptoms

Leaking
Leaks water
Will not drain
See more...

Installation Instructions

Jerry from Aransas Pass, TX

Agitator not working correctly and leaking from somewhere underneath.

I watched the videos before I ordered the part and when the order arrived I replaced the parts with no problems. The most time consuming part of the job was cleaning the washer. You will be surprised to find what will accumulate down there after years of service. The order came in in record time so this site gets an A+ for being fast and accurate. No back-orders either. I will surely use for any-other parts I need in the future. Read more...

Kenmore Washer Parts

Popular Kenmore Washer Parts

Appliance Type

Related Pages

Popular Kenmore Washer Models

Kenmore Washer Parts

Start With Your Model Number

Popular Kenmore Washer Parts

Appliance Type

Related Pages

Popular Kenmore Washer Models