Models > 11045862400

11045862400 Kenmore Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Manuals & Guides for 11045862400

Click to download
Keep searches simple, eg. "belt" or "pump".
In Stock
This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle. Sold individually.
In Stock
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
In Stock
This part is used on front load washers and includes the interlock switch assembly.
In Stock
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
In Stock
Shock absorbers help keep the washer from vigorous shaking during its cycles. Sold individually.
In Stock
$104.96
This part continually measures the amount of water entering the tub. It will make adjustments if too much or too little water is present.
In Stock
$7.91
Metallic screw that is less than an inch long. Does not include the plastic washer.
In Stock
Attaches to door lock mechanism.
In Stock
Used to help hold your bellow in place on your washer.
In Stock
$52.80
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear. NOTE: Per Manufacture, belt measures 48.22" long uninstall...
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
February 8, 2024
The water only runs for a minute and never makes it to the window,
For model number 11045862400
Fix.com logo
Hi Brian, Thank you for your question. If your washer starts to fill with water and then stops, we would recommend checking the water inlet valve, the door lock latch, and the electronic control board. We hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:

Common Problems and Symptoms for 11045862400

Viewing 13 of 13
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing
How to fix it
Draining Issues
Fixed by these parts
Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Franck from Annandale, VA
Parts Used:
WP8182119
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Bellows were moldy, needed to replace
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will fin d a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow.
Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.

The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily.
When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow.
Push as much of the bellow into the washer as possible to get it out of the way.

Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket.
This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way.
Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart.
You can now remove the entire hose clamp from around the bellow by pulling it forward.
You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out.
Pull the old bellow completely out, very easy to do.

Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side.
You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.

Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force.
As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.

Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop.
Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.

Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w
364 of 391 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Donald from Wichita, KS
Parts Used:
280187
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Socket set
Washer would not drain ,F02 and SUD code displaying
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout i n the front of the pump, using the water vac to catch the water as it leaked out.
(5) I removed the wiring to the motor.
(6) I removed the screw that holds the pump in place with a Torx T-20 socket.
(7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ).
(8) I tested the pump and found it would run but was making a lot of noise and running slow.
(9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4).
Don Kramer
Wichita, Kansas
233 of 245 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Vilonia, AR
Parts Used:
WP8182634
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to p opening.
7. reverse order to finish.
194 of 234 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!