Models
>
79641162410
79641162410 Kenmore Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for 79641162410
Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
$74.11
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order within the next 9 hrs and your part ships today!
$26.80
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
Order within the next 9 hrs and your part ships today!
$72.90
If your washing machine is leaking, slow to fill, will not stop filling with water, or is not filling at all, the cold-water inlet valve may be defective. The purpose of the valve is to open to allow ...
In Stock
Order within the next 9 hrs and your part ships today!
$41.72
This hose has bellows to allow for flexibility during the wash and spin cycles.
In Stock
Order within the next 9 hrs and your part ships today!
$27.79
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
In Stock
Order within the next 9 hrs and your part ships today!
$31.32
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
In Stock
Order within the next 9 hrs and your part ships today!
$116.67
This door boot is for washers.
Door boot forms a seal between the wash tub and the door, preventing leaks.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
In Stock
Order within the next 9 hrs and your part ships today!
$8.04
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
$30.78
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
In Stock
Order within the next 9 hrs and your part ships today!
In Stock
Order within the next 9 hrs and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard
March 14, 2023
LE code on the washer
For model number 79641162410
Hi Richard, thank you for the question. The LE error code means that the motor in your washer is locked. First, try resetting your washer. Sometimes the LE error code is displayed simply because the washer is overloaded and the motor stops being able to operate. If that is not the cause of the issue, then it may be due to excessive detergent. If you see lots of suds in the tub, let the washer sit idle for 30 minutes so the foam dissipates. Next, start a Drain/Spin cycle to remove the sudsy water. Then run a new cycle without adding any detergent to wash and rinse the current load. If your washing machine is still showing the LE error code, then the next step is to check the rotor. When the rotor becomes faulty, your washer will not be able to work. The part number for the rotor assembly is FIX3532774. If the problem persists, you may need to check the motor stator, part number FIX11709149. The motor stator works with the motor rotor to rotate the spin basket. If it is faulty, you may need to replace it. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Common Problems and Symptoms for 79641162410
Viewing 10 of 10Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Engine runs but does not pump water
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Lid or door won’t close
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Apple Valley, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read more
e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from STOWE, VT
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
leaking tub-to-pump drain hose
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RALEIGH, NC
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this instruction helpful to you?
Thank you for voting!