Jump to:
Product Description
This hose has bellows to allow for flexibility during the wash and spin cycles.
-
Works with the following brands:LG, Kenmore
-
Works with the following products:Washer, Washer Dryer Combo
-
Fixes the following symptoms:Leaking, Will not drain
-
Part# 4738ER1002A replaces these:AP4436407, 1266823, 4738ER1002A, 4738ER1002, 4738ER1002A, 4738ER1002B
- Works with the following brands:
- LG, Kenmore
- Works with the following products
- Washer, Washer Dryer Combo
- Fixes the following symptoms
- Leaking, Will not drain
- Part# 4738ER1002A replaces these:
- AP4436407, 1266823, 4738ER1002A, 4738ER1002, 4738ER1002A, 4738ER1002B
Part Number Cross Reference
Videos For installing this part.
Replacing your Tub-to-Pump Drain Hose
Questions and Answers
Be the first to ask our experts a question about this part!
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts Additional or alternate parts to consider.
Installation Instructions Provided by Fix customers like you.
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
- Customer:
- Derrick from Hammonton, NJ
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Drain hose had 2 slits in the bellows.
Used a Phillips head screw driver remove the band clamp from the main tub drain(easy). Then used a pair of pliers to release spring clamps(1 @ the pump and 1 @ the over flow drain). Removing the Hose was easy, replacing was a bit difficult only because connecting the hose to the pump took a lot of time getting the spring clamp in the righ
... Read more
t position and making sure I didn't cut the hose, surly the hardest part of the operation. Secured band clamp and spring clamp. Op's normal.
Read less
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candyce from Minneapolis, MN
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
Bellows leaked
Removed original bellows and replaced with new part. The replacement was very straightforward, but it took a little over an hour due to the inaccessibility of the area and difficulty of getting the clamps on the ends of the tubing and slipping those ends over the appropriate connection points. It's necessary to reach into the rear of the
... Read more
washer, almost to the front, in order to put the front of the bellows part on the connection. There isn't a lot of room to work, though the washer was pulled far enough from the wall to have room to move around.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Orem, UT
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small hole in the bellows which caused a leak.
I tipped the washer back so it would stay without falling. The new part is installed on the bottom of the machine. I used a large pair of slip joint pliers to expand and slide off the hose clamps from the front and back of the bellows assembly. A Phillips screwdriver undid the center clamp in the middle of the bellows assembly. Have a
... Read more
towel under the area to absorb the 1/2 pint or so of the water that will come out. When installing the new part, first slide the clamps on each end and set the big wire clamp in the center. Install the front end of the part first and put the clamp in its place with the pliers. Then secure the large part to the center area and tighten that clamp with the screwdriver. Finally attach the back end of the part to its location and place the clamp where it goes. Carefully set the washer on its feet, plug it in, start it up and check for leaks. You're done.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Arroyo Grande, CA
- Parts Used:
- 4738ER1002A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
bellows tear from tub movement
The tub to pump hose is very easy to get to if you remove the following. 1: remove the 4 Phillips screws holding the two plastic clips at the top rear of the machine. 2: push the top metal panel to the rear and remove. 3: remove two screws on either side of the soap dispenser and un- clip the plastic tabs which attach the control panel
... Read more
and move to expose four 10mm hex head screws.4: remove the door gasket clamp spring wire and save for reinstallation. 5: Remove the lint screen door and two Phillips head screws. Drain the pump via the drain hose into a quart container. 6: remove the plastic pump cover to expose one Phillips head screw and remove. 7: remove the four 10mm screws under the control panel. 8: grasp the front cover tilt the front panel towards you and lift up and remove. You can now access the tub to pump bellows.
Read less
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
★
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
James G - March 26, 2020
Verified Purchase
Fit perfect
Perfect fit. I was able to install from rear without opening the front. Fixed the leak.
Model Compatibility
This part works with the following models:
Fix Number: FIX3523345
Manufacturer Part Number: 4738ER1002A
Manufacturer Part Number: 4738ER1002A
| Brand | Model Number | Description |
|---|---|---|
| LG | 048231017473 | Washer - Model Lg 048231017473.Abwevus Washer – Common Parts And Diagrams |
| LG | 40262 | Washer |
| LG | 40272 | Washer - LG Washing Machine Model 40272 Parts |
| LG | 40277 | Washer |
| LG | 40311 | Washer - Washer |
| LG | 40315 | Washer |
| LG | 40318 | Washer - LG Washing Machine Model 40318 Parts |
| LG | 40441 | Washer - LG Washing Machine Model 40441 Parts |
| LG | 40445 | Washer |
| LG | 40448 | Washer - LG Washing Machine Model 40448 Parts |
| LG | 40512 | Washer - LG Washing Machine Model 40512 Parts |
| LG | 40518 | Washer - LG Washing Machine Model 40518 Parts |
| LG | 40776 | Washer |
| LG | 40996 | Washer |
| LG | 41002 | Washer - LG Washing Machine Model 41002 Parts |
| LG | 41003 | Washer - LG Washing Machine Model 41003 Parts |
| LG | 41022 | Washer - LG Washing Machine Model 41022 Parts |
| LG | 41025 | Washer |
| LG | 41028 | Washer - LG Washing Machine Model 41028 Parts |
| LG | 41029 | Washer - LG Washing Machine Model 41029 Parts |
| LG | 41072 | Washer - LG Washing Machine Model 41072 Parts |
| LG | 41073 | Washer - LG Washing Machine Model 41073 Parts |
| LG | 41162 | Washer - LG Washing Machine Model 41162 Parts |
| LG | 41172 | Washer - LG Washing Machine Model 41172 Parts |
| LG | 41182 | Washer - LG Washing Machine Model 41182 Parts |
| LG | 41262 | Washer - LG Washing Machine Model 41262 Parts |
| LG | 41272 | Washer - LG Washing Machine Model 41272 Parts |
| LG | 41282 | Washer - LG Washing Machine Model 41282 Parts |
| LG | 41283 | Washer - LG Washing Machine Model 41283 Parts |
| LG | 41302 | Washer - LG Washing Machine Model 41302 Parts |
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.