Heater Parts

Filter Kit

$18.69

Fix Number: FIX10469007
Manufacturer Part Number: 70-054-0100

This part is sourced directly from Pro Temp and is an OEM approved replacement part for certain Kerosene/Diesel Forced Air Heaters manufactured by Pro Temp, Heat Hog, Heat Stream, and Master. For full compatibility, please see the "Model Cross Reference List" below. The filter is responsible for preventing dust and debris from entering and damaging the motor assembly. These filters must be changed with regular use; we recommend replacing them every 6 months to 1 year, depending on the frequency of use. If your heater begins to perform poorly, it likely is time to change the filters. Kits are sold individually, and each kit contains the intake, output, and lint filters.

High Limit Sensor Heat Exchange

$5.70

Fix Number: FIX10369236
Manufacturer Part Number: 60015

Burner Tile

$15.40

★★★★★

2 Reviews

Fix Number: FIX10424783
Manufacturer Part Number: 73439

This is an authentic OEM replacement part sourced directly from the manufacturer, it is compatible with select heaters manufactured by Mr. Heater. To ensure it fits your heater, please see the "Model Cross Reference List" below. This burner tile is used in portable heaters to help stabilize the flame and assist in the radiation of heat. This burner tile is made of ceramic and tends to wear out over time due to the extreme heat it is exposed to. If your Burner Tile is damaged, cracked, or discolored, it needs to be replaced. The burner tile is sold individually and has dimensions of 6.5"L x 4"W x 1"T.

Installation Instructions

CHUCK from NEOTSU, OR

Product showed up broken. Twice

I have not repaired my Mr
Heater yet. I sent all 4 ceramic tiles and gaskits back and am waiting on a refund. Ceramic tiles are like glass and even though instructed to by me. The product was sent in a flimsy package. I will purchase elsewhere. So far this process has taken over one month. Read more...

Cover with Fan Motor

$68.56

★★★★★

5 Reviews

Fix Number: FIX12044864
Manufacturer Part Number: E78404

Installation Instructions

Chris from HERMISTON, OR

Add convection to heater by installing a cover with fan motor

Removing the 4 screws on the cover was the easy part! Once the screws are removed, you will need to push upward as the cover is clipped in. Installing the new cover with fan is tricky since-First, you need to make sure you don't sever any wires when installing the new cover. The main trick though is you have to position the cover in place immediately high in place and push straight downward as it should clip back into place. Takes a little finesse but I finally got mine to go in correctly. Read more...

Spark Plug Kit

$13.70

Fix Number: FIX10469005
Manufacturer Part Number: 70-052-0200

Designed for Pro Temp Heaters, this OEM approved replacement Spark Plug is compatible with many models of Pro Temp, Heat Hog, Heat Stream, and Master Heaters. For full compatibility, please see the "Model Cross Reference List" below. If your heater does not turn on, you may have a faulty Spark Plug. This Spark Plug is approximately 3" in length, and the kit includes the bolt and washers needed for installation. Each Kit is sold separately.

Heating Element

$75.98

Fix Number: FIX12098594
Manufacturer Part Number: S97020888

This is an OEM heating element for use with ventilation fans and ceiling heaters. Some units allow you to turn the heating function on or off. They are most commonly found in bathrooms to help heat the room. For this repair, you will start by removing the fan cover, disconnect the wire, and remove the nuts. You will then be able to pull the heating element fan housing out, remove the screws, and remove the heating element. The installation of the new part is conducted in the reverse order.

Installation Instructions

Loretta from BRIGHTON, CO

Heater element went out

Took off light cover took out heater blower and heat element. Replaced heat element and put all back together Read more...

Tile, Gasket

$4.99

★★★★★

1 Review

Fix Number: FIX10424782
Manufacturer Part Number: 73433

Electrode Sensor

$5.60

Fix Number: FIX12031770
Manufacturer Part Number: 60141

Switch, ON/OFF, 20 amp

$12.39

★★★★★

4 Reviews

Fix Number: FIX12053859
Manufacturer Part Number: 3870001

This OEM approved replacement part is compatible with various models of Sunheat appliances. For full compatibility, please see the "Model Cross Reference List" below. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. This switch has 3 prongs coming out of the back and can be removed by squeezing the two tabs on the side of the Switch. Switches are sold individually.

Ignitor (Updated)

$70.99

★★★★★

3 Reviews

Fix Number: FIX12051602
Manufacturer Part Number: 70-037-0350

This is a genuine replacement part sourced directly from Pro Temp. It is compatible with multiple models of Heaters manufactured by Pro Temp, Heat Hog, Heat Stream, and Master. To ensure your Heater is compatible with this part, please see the "Model Cross Reference List" below. The Ignitor is responsible for lighting the heater if your heater will no longer light properly, but the gas is flowing, you may need a new Ignitor. Each Ignitor is sold individually. NOTE: This is the latest version of the part, a plug adapter (Part #70-037-5000) may be required depending on your model.

Popular Heater Parts

Installation Instructions

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Heater Models

Heater Parts

Start With Your Model Number

Popular Heater Parts

Installation Instructions

Installation Instructions

Installation Instructions

Brands

Related Pages

Popular Heater Models