Pro Temp Heater Parts

Fix Number

FIX10469005

Manufacturer Part Number

70-052-0200

Designed for Pro Temp Heaters, this OEM approved replacement Spark Plug is compatible with many models of Pro Temp, Heat Hog, Heat Stream, and Master Heaters. For full compatibility, please see the "Model Cross Reference List" below. If your heater does not turn on, you may have a faulty Spark Plug. This Spark Plug is approximately 3" in length, and the kit includes the bolt and washers needed for installation. Each Kit is sold separately.

Fix Number

FIX10468983

Manufacturer Part Number

70-035-0300

This is an authentic component which is sourced directly from the original equipment manufacturer for use with kerosene forced air heaters. The line is utilized to carry the air between the combustion chamber and the fan assembly. Unfortunately, over time the material will wear out and may begin to crack eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality component is made of durable rubber and is sold individually.

Fix Number

FIX10469008

Manufacturer Part Number

70-055-0100

Fix Number

FIX10468971

Manufacturer Part Number

70-027-0300

Sourced directly from the manufacturer, this part is designed for use on various Heaters made by Heat Hog, Heat Stream, Master, and Pro-Temp. For full compatibility, please see the "Model Cross Reference List" below. The Main PCB Assembly connects to the thermostat control knob and the fuse. If your heater will not turn on properly, inspect your Main PCB assembly for physical damage, if it has damage or burn marks, it needs to be replaced. This Main PCB Assembly measures approximately 8"x3". Each Assembly is sold individually.

Fix Number

FIX10468915

Manufacturer Part Number

70-003-0100

This item is a genuine OEM sourced replacement part that is intended to be used with forced air heaters from Pro Temp, Heat-Stream, Heat Hog, and Master. The plastic fuel filter connects to the fuel line and is used to prevent contaminants from entering the motor assembly. This item is available as an individual replacement part.

Fix Number

FIX10468967

Manufacturer Part Number

70-025-0100

This is an authentic OEM sourced replacement gauge which is specially designed for use with kerosene heaters. The gauge registers pressure readings, over time it may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality item is made of durable materials and is sold individually. Please make sure to refer to the appropriate diagrams of your specific model for the correct location and application of this item.

Fix Number

FIX17016835

Manufacturer Part Number

70-016-1000

This is a photocell designed for use in space heaters to detect the presence of a flame, ensuring that the burner ignites and remains lit to provide heat while preventing the release of unburned gas. This photocell is a genuine OEM part, sold individually, and is compatible with various heater models. It is typically attached to the main combustion chamber with a bracket (sold separately). Factors like dirt and debris, aging, and exposure to higher temperatures can lead to photocell failure. A failing photocell can result in your heater not starting, starting intermittently and then shutting down, and sometimes displaying error codes related to the photocell. To replace this part, you will need a screwdriver and/or socket wrench, as well as a set of pliers. Begin by disconnecting the heater from its power source and draining the fuel from the heater. Remove the top, back, and side covers of the heater to access its internal components. Locate the photocell within the heater, disconnect its cable and the photocell itself, and then install the new photocell. Reassemble your heater, ensuring that any disconnected wires are properly reconnected.

Fix Number

FIX17016834

Manufacturer Part Number

70-036-1010

This is a genuine OEM replacement part designed for use with Pro Temp, Heat Stream and Master kerosene forced air heaters. The line is utilized to deliver the fuel from the tank into the carburetor. When you press the primer bulb, it will purge all the air out of the carburetor and fill its chambers with fuel. The excess fuel is then forced back into the tank through the return line. Unfortunately, over time lines will become brittle and may begin to crack eventually requiring a replacement. Keep in mind this high-quality part is made of durable rubber and is sold individually.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX12051602

Manufacturer Part Number

70-037-0350

This is a genuine replacement part sourced directly from Pro Temp. It is compatible with multiple models of Heaters manufactured by Pro Temp, Heat Hog, Heat Stream, and Master. To ensure your Heater is compatible with this part, please see the "Model Cross Reference List" below. The Ignitor is responsible for lighting the heater if your heater will no longer light properly, but the gas is flowing, you may need a new Ignitor. Each Ignitor is sold individually. NOTE: This is the latest version of the part, a plug adapter (Part #70-037-5000) may be required depending on your model.

Fix Number

FIX10468949

Manufacturer Part Number

70-019-0100

It is a genuine item that is supplied by the original equipment manufacturer. This part is made for use with kerosene forced air heaters. The thermostat acts as a sensor which protects the unit from overheating. Unfortunately, over time it may wear out, get damaged or stop working all together eventually requiring a replacement. Note, this high-quality thermostat limit control is sold individually. To replace it, you will need a screwdriver to take the housing apart. Make sure to refer to the owner's manual and the appropriate diagrams for your model to ensure the correct application.