General Electric Washer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
General Electric Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular General Electric Washer Parts

ROD & SPRING Assembly LEFT - WHITE – Part Number: WH16X26911
ROD & SPRING Assembly LEFT - WHITE
$24.00
In Stock
Fix Number
FIX12343381
Manufacturer Part Number
WH16X26911
If your washer is shaking or making loud noises during the spin cycle, this left-side suspension rod and spring assembly might be the fix you need. It helps keep the drum stable and reduces vibration for a smoother, quieter wash. Since all four suspension rods wear at a similar rate, it’s a good idea to check the others when replacing this one. This part is sold individually and doesn’t include the other rods. For safety, unplug your washer and wear gloves before starting the repair.
Fixes these symptoms
AUGER – Part Number: WH43X31240
AUGER
$55.18
In Stock
Fix Number
FIX16226232
Manufacturer Part Number
WH43X31240
Located in the center of the washer tub, this white spiral auger helps move clothes through the water and detergent during each cycle. It lifts and drops garments to break up dirt and stains. If your washer is making strange noises, leaving clothes tangled, or not cleaning properly, the auger may be worn or damaged. Replacing it is a straightforward fix that can improve your washer’s performance. Be sure to disconnect power before starting the repair.
Fixes these symptoms

Installation Instructions

gary from CUYAHOGA FLS, OH
The agitator moves freely from the tub.
Remove the auger (the spiral shaped part) by putting a Philips screw driver with at least 4" long shank into the hole at the base the auger (you'll have to feel for it as it isn't visible from the top), and hold the agitator with the one hand and smack the screw driver handle clockwise. It should turn 1/4 turn, then lift the auger off the agitator. After removing the auger (looking straight down) you'll see the bolt that holds on the agitator. With a 7/16 socket on an extension, (while holding the agitator) turn counter-clockwise the bolt. After removing the agitator you'll likely see a grayish colored paste caked on the drum and transmission shaft clean it up with damp clothes, as well the shaft making sure there is no residue left on the splines of the shaft.
Now you are ready to reassemble, doing everything opposite of the removal. Read more...
CLUTCH – Part Number: WH05X24185
CLUTCH
$38.97
In Stock
Fix Number
FIX11729473
Manufacturer Part Number
WH05X24185
Fixes these symptoms
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • Spins slowly
  • See more...
SPRING CLUTCH – Part Number: WH01X24434
SPRING CLUTCH
$16.33
In Stock
Fix Number
FIX11763251
Manufacturer Part Number
WH01X24434
Fixes these symptoms
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • Will not agitate
  • See more...
LID LOCK SERVICE KIT – Part Number: WH08X37938
LID LOCK SERVICE KIT
$79.61
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX17626546
Manufacturer Part Number
WH08X37938
This replacement lid lock keeps your washing machine door securely closed during the wash cycle. If the washer won’t run or the lid won’t stay locked, this part may need replacing. Installation is simple: disconnect power and wear gloves. Sold as a single unit.
Fixes these symptoms
  • Cycle Not Advancing
  • Lid or door won’t close
  • Locking Issues
  • See more...

Installation Instructions

Don from FAIRFIELD, OH
Washer wouldn’t run.
Just follow the instructions they are laid out and easy to follow. New switch parts are much better than original parts I replaced. Read more...
Pump Drain Assembly – Part Number: WH23X28418
Pump Drain Assembly
$53.52
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12723115
Manufacturer Part Number
WH23X28418
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
Fixes these symptoms
MODE SHIFTER – Part Number: WH03X30517
MODE SHIFTER
$51.43
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX16554752
Manufacturer Part Number
WH03X30517
If your washer isn’t spinning or agitating like it should, this shift actuator might be the fix you need. It helps your machine switch between wash and spin cycles, and is usually found underneath the washer. Made from sturdy plastic, it’s easy to install with just a couple of screws and a wire harness connection. If your washer won’t start or seems stuck in one mode, replacing this part could get things running smoothly again. Sold individually.
Fixes these symptoms
  • Cycle Not Advancing
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • See more...
Agitator – Part Number: WH43X30957
Agitator
$80.10
In Stock
Fix Number
FIX16542670
Manufacturer Part Number
WH43X30957
This agitator assembly is designed for use in top-load washing machines, where it plays a crucial role in the cleaning process by rotating back and forth to help lift and move clothing through water and detergent. If your current agitator is cracked, worn, or no longer functioning properly, replacing it can restore your washer’s performance and ensure your laundry is thoroughly cleaned. Installation requires a wrench and should be done with the power and water supply turned off for safety. This component is sold individually and does not include additional parts or accessories.
Fixes these symptoms
  • Marks left on clothes
  • Spinning Issues
  • Will not agitate
  • See more...
DRIVE BELT – Part Number: WH01X24180
DRIVE BELT
$27.83
In Stock
Fix Number
FIX11736832
Manufacturer Part Number
WH01X24180
Fixes these symptoms
  • Burning smell
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • See more...
Water Inlet Valve Assembly – Part Number: WH13X26535
Water Inlet Valve Assembly
$49.29
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12726769
Manufacturer Part Number
WH13X26535
This replacement water inlet valve ensures accurate control of hot and cold water entering your washing machine. It plays a key role in maintaining proper water levels for each cycle. If your washer won’t fill, leaks, or fills unexpectedly, the valve may need to be replaced. The assembly is gray, encased in plastic, and does not include a gasket. Installation requires basic tools and should be performed with the appliance unplugged and water supply turned off.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

General Electric Washer Appliance Types

Related General Electric Washer Parts

Popular General Electric Washer Models

View More
+