Drill Press Parts

Brush Holder Assembly

$11.58

Fix Number: FIX10122286
Manufacturer Part Number: 22-20-0150

This is an authentically sourced OEM brush holder assembly for drills. The assembly includes, the metal brush holder, brush with lead wire and the spring. For most models, this repair will require both brush replacements, so you will may need to order two of these in most cases. Carbon brushes are a common wear component that require regular maintenance.

Spring With Housing

$32.95

Fix Number: FIX10315886
Manufacturer Part Number: 1310084

This is a genuine OEM sourced replacement part designed for use with a drill press. It allows height adjustment handle to retract. It is made out of metal and it is sold individually. This assembly includes a metal spring, housing and a retainer. You would need a wrench to complete this repair.

Ball Bearing

$45.05

Fix Number: FIX10463888
Manufacturer Part Number: BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Adam from FREMONT, NE

Saw was making loud screeching noise and unsatisfactory cuts

1: disconnect power and remove blade
2: remove spanner nut
3: remove arbor nut. Spins opposite:
righty loosy lefty tighty
4: remove arbor with mallet and dowel
5: use arbor press to take off ball bearing
6: press on new bearing Read more...

Switch

$137.50

Fix Number: FIX10328665
Manufacturer Part Number: 905224

This is a switch for a variety of power tools. It is a commonly replaced part as it handles the on and off operations in your tool. This part will get damage over time because it uses mechanical internals. The most common reason for needing to replace the switch is if your tool has power but is not turning on.

Torsion Spring And Cap Assembl

$6.51

Fix Number: FIX16237360
Manufacturer Part Number: 089140314059

★★★★★

1 Review

Fix Number: FIX10315885
Manufacturer Part Number: 1310082

Genuine Delta replacement part, this part with 2 part. The Delta 1310082 Spring With Housing is the part of the drill presses listed below that returns the drill chuck back to its original position after using the drill press. This part contains the spring and the spring housing.

Carbon Brush

$13.17

Fix Number: FIX10122195
Manufacturer Part Number: 22-18-0701

This is an OEM carbon brush, sold individually. Your tool will require two of these, so please be sure to order what you need. It is best practice to replace both carbon brushes at the same time, even if only one appears worn. Worn brushes are a common reason for a malfunctioning motor, so it is important to inspect them regularly and replace them when needed. When you are inspecting the carbon brushes look for wear near the wire lead. If there are burns, this could be an indication that something is also wrong with the armature, so it should be checked as well.

SPRING PLATE

$24.32

★★★★★

1 Review

Fix Number: FIX18981888
Manufacturer Part Number: 5140077-86

This is a genuine OEM sourced replacement part designed for use with Porter Cable drill press. It allows height adjustment handle to retract. It is made out of metal and it is sold individually. You would need a wrench to complete this repair.

Plastic Knob

$6.51

Fix Number: FIX10130762
Manufacturer Part Number: 43-98-0050

This is a Genuine OEM Sourced replacement part used on Milwaukee Drill Press Stands. This item screws onto the Bar Handle and allows for a firm grip. This item is made out of Black Plastic and it is Sold Individually. No tools are required to replace.

Table Saw Switch

$43.95

★★★★★

10 Reviews

Fix Number: FIX10325609
Manufacturer Part Number: 489105-00

This Switch is an OEM approved replacement part for various tools and models manufactured by Delta, Black and Decker, and Porter Cable. For full compatibility, please see the "Model Cross Reference List" below. This Switch has four terminals, a removable safety key, and a compact design for easy installation. The purpose of the switch is to turn the device on/off, as well as playing a role in electric breaking by momentarily reversing electrical polarity. Due to the mechanical internals of switches, they tend to degrade and wear out over time, making them a commonly replaced part in power tools. Common symptoms of a broken switch include: the device has completely stopped functioning, it will not turn on, and turning off intermittently during use. Each Switch is sold individually, and may also be referred to as a Rocker Switch.

Installation Instructions

keith from EMPORIA, KS

Power switch would not turn saw off

unplugged power cord.
removed the nut holding the power switch assembly on the saw.
removed 3 screws from the back cover.
removed the 2 white wires and 2 black wires from the switch terminal post. pay attention to wire color on each post.
removed old switch from the bracket by squeezing the sides of the old switch to remove the switch from the bracket.
inserted the new switch in place in the opening.
re attached the wires to the spade terminal on the switch using the 4 terminals. black on the 2 posts top and bottom on one side and the other side white on the top and bottom.
re attach the switch assembly to the table saw
test operation Read more...

Popular Drill Press Parts

Installation Instructions

Installation Instructions

Drill Press Brands

Related Drill Press Parts

Popular Drill Press Models

Drill Press Parts

Start With Your Model Number

Popular Drill Press Parts

Installation Instructions

Installation Instructions

Drill Press Brands

Related Drill Press Parts

Popular Drill Press Models