OEM Jet Drill Press Parts & Accessories

Spring Cap Assembly

$32.93

Fix Number: FIX10465183
Manufacturer Part Number: JDP17DX-078

This is a genuine OEM replacement part for select Jet and Powermatic Drill Presses. For full compatibility, please see the "Model Cross Reference List" below. This assembly is made out of metal and includes the Cap, Coil Spring, and Spring Retainer Ring. The primary purpose of this part is to allow the drill bit to be moved up and down by providing spring-loaded tension to bring the shaft to its original position. If your assembly vibrates during operation, or will not return to its original position, it likely is time to replace the Spring Cap. Each kit is sold individually.

Ball Bearing

$48.35

Fix Number: FIX10463886
Manufacturer Part Number: BB-6202ZZ

This is an authentic OEM replacement part for certain models of Jet, Powermatic, and Wilton tools that is sourced from the manufacturer. To ensure that this will fit your tool, please see the "Model Cross Reference List" below. This part has an outer diameter of 1.5", and metal shielding on both sides. The bearing is used to reduce friction between two rotating parts. It keeps wear on the equipment to a minimum, and helps the mechanics run efficiently. Depending on how often you use your tool, your bearings will need routine replacement due to continual pressure on them. Signs of broken or failing Ball Bearings include squealing, screeching, or grinding noise when powering the device off. Each is sold individually.

Ball Bearing

$45.05

Fix Number: FIX10463888
Manufacturer Part Number: BB-6203ZZ

This ball bearing is 17 mm and fits a variety of gardening power tools. The ball bearing has two contact rubber seals on each side and two non-contact metal shields on each end as well. Tip: if your tools needs only one seal or shield, then take off one of the shields or seals from this ball bearing. Refer to the manual provided by the manufacturer for further installation instructions and a detailed diagram.

Installation Instructions

Adam from FREMONT, NE

Saw was making loud screeching noise and unsatisfactory cuts

1: disconnect power and remove blade
2: remove spanner nut
3: remove arbor nut. Spins opposite:
righty loosy lefty tighty
4: remove arbor with mallet and dowel
5: use arbor press to take off ball bearing
6: press on new bearing Read more...

Flat Washer, M8

$9.85

Fix Number: FIX10517157
Manufacturer Part Number: TS-1550061

This flat washer is designed to fit a variety of power tools. The washer helps distribute the pressure evenly between parts and has multiple applications depending on your specific tool. Check the diagram for the accurate location in your tool. *Please note: this part is sold individually.

Hex Nut

$35.15

Fix Number: FIX10467621
Manufacturer Part Number: TS-1540071

This is a hex nut for power tools. It is size M10, with a 1.5 thread pitch. This is the most common hexagonal fastener. It has internal threads that screw on to the shank of a hex cap screw, or a bolt.

Flat Washer

$8.75

Fix Number: FIX10467627
Manufacturer Part Number: TS-1550031

This flat washer fits the following tools: saws, drills, planer jointers, and angle grinders. The washer helps prevent nuts and bolts from tearing or pulling through material because it creates a bearing surface. *Please note: This part is sold individually. Refer to the diagram provided by the manufacturer for installation instructions. Remember to unplug or turn off power on tool before beginning this installation.

Hex Nut

$9.85

Fix Number: FIX10467496
Manufacturer Part Number: TS-0561052

This is an authentic OEM sourced replacement component which is specially made for use on Jet and Powermatic equipment. It is a standard hardware which has multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this item. Keep in mind this high-quality hex nut is made of durable metal and is sold individually.

Hex Nut

$10.95

Fix Number: FIX10467494
Manufacturer Part Number: TS-0561031

1/8 Inch- 3/4 Inch Chuck

$218.50

Fix Number: FIX10380129
Manufacturer Part Number: 561709

This is an authentic OEM sourced replacement chuck which is specially designed for use with a Jet drill press. It is the component which allows a user to secure the drill bit, if your drill's bit retention is suffering, the rotation feels stiff, or the chuck has seized up entirely, a new chuck should fix the problem. This high-quality metal part is sold individually, the chuck key is included.

Hex Nut

$8.75

Fix Number: FIX10467493
Manufacturer Part Number: TS-0561011

It is a genuine replacement part which is supplied by the original equipment manufacturer for use with Powermatic, Jet and Wilton power tools. This special hex nut has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location and use of this hardware. It is a durable metal component which is sold individually, you will need a wrench to secure or remove it.

Jet Drill Press Parts

Popular Jet Drill Press Parts

Installation Instructions

Jet Drill Press Appliance Types

Related Jet Drill Press Parts

Popular Jet Drill Press Models

Jet Drill Press Parts

Start With Your Model Number

Popular Jet Drill Press Parts

Installation Instructions

Jet Drill Press Appliance Types

Related Jet Drill Press Parts

Popular Jet Drill Press Models