Kelvinator Parts

★★★★★

★★★★★

1 Review

Fix Number

FIX437595

Manufacturer Part Number

316048413

This OEM drip bowl fits under 8-inch burner elements and has a diameter of approximately 10-inches. Drip bowls catch any spills, and are a quick, easy, and cheap way to improve your cooktop aesthetic. While the replacement may be visually different from the original, it will fit your appliance. If your drip bowl has become discolored, corroded, or otherwise damaged, it needs to be replaced. This drip bowl is sold individually, so if you would like to replace all 4 drip bowls on your appliance you will need to account for this. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.

★★★★★

★★★★★

1 Review

Fix Number

FIX429854

Manufacturer Part Number

240337103

This authentic replacement crisper pan, also known as a vegetable drawer, inserts into the refrigerator crisper area. It is used to hold produce and maintain an ideal temperature to help preserve them as long as possible. The pan is clear plastic and measures roughly 11 inches deep, 22 inches long, and is sold individually.

Fix Number

FIX17219658

Manufacturer Part Number

5304535379

This lower dishrack assembly is a genuine OEM replacement part designed for select Frigidaire dishwashers. Finished in grey, it provides a sturdy and organized space to hold dishes, cookware, and utensils securely during the wash cycle. Its rust-resistant construction ensures long-term durability, even with frequent use. The rack is engineered to promote proper water circulation and spacing, helping to prevent damage to dishes and improve cleaning performance. Installation is simple—just slide the new rack into place. No tools are required. Sold as a complete assembly.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX9495545

Manufacturer Part Number

809006501

This dishwasher door gasket is attached to the bottom of the door, creating a strong seal between the tub and the outer edge of the door. This seal is prone to wear and tear due to its constant exposure to water, detergent, and food particles. If the gasket appears cracked, broken, or you notice a leak coming from the door, it will need to be replaced immediately. This gasket measures approximately 23 inches long. For this simple repair, no tools are necessary. Open the dishwasher door and remove the bottom rack. The gasket is located right along the bottom of the door, molded inside the channel. It is held in place in the groove across the bottom. Remove the old gasket by pulling it out with your hands. Take your new silicone gasket and line it up so the notch fits into the groove and slide it in place until it is secure. Reinstall the lower dishrack. We recommend leaving the door closed for a few hours to ensure the gasket is sealed tightly.

★★★★★

★★★★★

4 Reviews

Fix Number

FIX12585623

Manufacturer Part Number

5304517203

This is a single lower spray arm found in dishwashers to spray water and detergent vigorously over the dishes. This spray arm is made of plastic, so can warp or crack with time. The holes in the spray arm can get clogged with debris, so it should be cleaned every so often. If it is beyond cleaning or damaged, it will need to be replaced. If the holes are clogged, this can sometimes mean there is a problem with the filter system, so it is a good idea to inspect this as well. For this repair, start by turning off the water supply to the dishwasher. Pull the lower rack out of the dishwasher and out of the way. Remove the lower wash arm. Using a flathead screwdriver, push the small locking tabs located on each side at the bottom of the spray arm. You should now be able to easily pull the spray arm out of the dishwasher. Align the new lower wash arm and push it down to secure it in place. Make sure it can spin freely and is not making contact with the heating element. Place the lower dishrack back into the appliance and close the door.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX438018

Manufacturer Part Number

316075103

This genuine OEM bake element is located on the bottom of the oven cavity to supply heat for baking. The approximate size is 19-1/2 inches wide by 18-1/2 inches long and has 3-1/2 inch inserts. The element terminals are male quarter inch spade connectors and have push-on wire terminals. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. Please remember to disconnect the power to your oven before you start your repair. Next, remove the 2 screws securing the old element, pull it out, and discard. Connect the new element prongs where the old element fit and screw it back in place. This is a very simple repair that anyone can do.

Fix Number

FIX1148434

Manufacturer Part Number

134503600

The drum belt, also known as a drive belt, is a rubber piece that wraps around the dryer drum, idler pulley, and motor pulley and is used to make the drum rotate. If you can hear the motor running, but the drum is not spinning, it may be an issue with the drum belt. Since it is made of rubber, it can become brittle with age causing it to break. Alternatively, it could be stretched out and no longer gripping to the dryer drum. Both of these issues would require you to replace the belt. To do this repair you will need a putty knife to pop open the top and front panel of your dryer, and a Phillip head screwdriver. Be sure to disconnect the power to your appliance before beginning your repair. This drum belt measures 88 and 3/4 inches long by 1/4 inch wide. As it is a genuine OEM part, this size will be compatible with your appliance model.

★★★★★

★★★★★

1 Review

Fix Number

FIX430917

Manufacturer Part Number

240530701

The drawer track support provides support for the right side of the sliding drawer to help it move open and closed easily. This part is sold individually, so if you also require the left side rail it will need to be ordered separately. It measures roughly 16 inches long by 1 inch high. If it is damaged it might make it difficult to open and close the fresh food drawer. Check the support rails in case something is blocking it. It is important to replace a damaged rail to prevent it from damaging the drawer itself. The only tool required for this repair is a Philips screwdriver. Remove the entire upper shelf from the inside of the fridge. Place the assembly on a flat work surface. Remove the screws on the back holding the back rail in place. Next, disengage the tabs holding the old right side rail in place. When installing the new one, line up the slotted opening on the rail to the tabs on the drawer and push it in until it snaps into place. Reinstall the back rail with screws. Check the operation of the drawer and place it back into the refrigerator.

★★★★★

★★★★★

1 Review

Fix Number

FIX734935

Manufacturer Part Number

240534901

This is a genuine door shelf retaining bar for a refrigerator. It attaches to the inside of the door on the refrigerator and helps to secure items placed on the shelf. It is made of white plastic and can be easily installed without the use of tools. Start by making sure the projection on the inner door panel fits into the recessed area at the top of the shelf retainer bar. Once they are lined up, press it into place until you hear a snap. This part measures approximately 25-inches wide, 3-inches high, and 5-inches deep. If it breaks, cracks or warps over time, it will need to be replaced. This part is sold as an individual part. We recommend taking this opportunity to inspect the other shelf retaining bars for damage in case they also need to be replaced at the same time.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX437596

Manufacturer Part Number

316048414

This drip bowl is an OEM approved replacement part designed for use with various electric ranges and cooktops. This part is located underneath the burner to contain any spills while cooking. It fits under 6-inch burner elements and has a diameter of approximately 8-inches. While the replacement may be visually different from the original, if you have used your correct model number to search, this will fit your appliance. Common reasons to replace this often neglected part is if it has become discolored, corroded, or otherwise damaged. Each drip bowl is sold individually. This is a good time to inspect all drip bowls on the appliance, if you would like to give your appliance a fresh look, keeping in mind that they may be different sizes and are sold separately. No tools are required for installation, simply line up the hole on the bowl with the terminal block and drop it into place.