Husky Parts

★★★★★

★★★★★

4 Reviews

Fix Number

FIX9988561

Manufacturer Part Number

647-04271-0637

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.

Fix Number

FIX11813755

Manufacturer Part Number

954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Fix Number

FIX16463287

Manufacturer Part Number

942-04308A

Fix Number

FIX9092936

Manufacturer Part Number

712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Fix Number

FIX19305064

Manufacturer Part Number

946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

Fix Number

FIX17055954

Manufacturer Part Number

736-0524B-1

This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made of metal to ensure a long life. If there is visible damage or wear, replace this part.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX12508562

Manufacturer Part Number

N286039

This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.

Fix Number

FIX9096195

Manufacturer Part Number

714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

★★★★★

★★★★★

1 Review

Fix Number

FIX9186148

Manufacturer Part Number

954-0467A

This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit. Make sure to clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Loosen the transaxle pulley • Relieve tension on the upper drive belt • Remove the upper drive belt and lawn mower belt guide • Secure the new belt • Reassemble and tighten the pulleys

★★★★★

★★★★★

1 Review

Fix Number

FIX11813377

Manufacturer Part Number

946-05124A

This is an authentic OEM part. The MTD deck engage cable is composed of metal and plastic parts, and has been designed for use in several tractor machines. This part is fastened onto the frame assembly. The deck engage cable works to move belt idler pulley and engage the cutting blades. Please refer to manual for specific repair instructions. A wrench and a screwdriver is helpful in making the replacement. This part is sold individually.