Husky Compressor Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
Husky Appliance Parts
Shop By Appliance Type

Popular Husky Compressor Parts

Svc Compressor Pump Cw 75 X 51Mm – Part Number: VT4923
Svc Compressor Pump Cw 75 X 51Mm
$331.09
In Stock
Fix Number
FIX17016290
Manufacturer Part Number
VT4923
Svc Compressor Pump Cw 75 X 51Mm
Manifold – Part Number: E108508
Manifold
$75.21
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12099613
Manufacturer Part Number
E108508
This manifold ensures even gas distribution to your equipments burners, delivering consistent heat for efficient cooking. Made from heavy-duty metal, it withstands high temperatures and daily use.
Fixes these symptoms
Outlet Tube – Part Number: E108525
Outlet Tube
$59.30
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12099629
Manufacturer Part Number
E108525
This part includes one genuine OEM outlet tube for an air compressor. This outlet tube will fit up to 80 gallon air compressors, meaning it will also work with 20-gallon units. This part transfers the air between the cylinder and the tank. It is made out of aluminum, which assists in cooling the air as it travels out of the cylinder. Due to the constant vibration of an air compressor while its un use, over time, the ends of the tube can start to deteriorate and will leak. Please note that the O-rings are not included and will need to be purchased separately if they are needed.
Fixes these symptoms

Installation Instructions

Russell from ALVIN, TX
Regulator control knob
Remove screw on back of motor, put thread seal on nipple both ends screwed in place tighten up with 3/4 open end wrench until line up replace screw back of motor, install both gauges and pressure relief valve , started compressor tested with soapy water for leaks. Read more...
Watch the install video
DRAIN VALVE – Part Number: N286039
DRAIN VALVE
$7.91
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX12508562
Manufacturer Part Number
N286039
This is a single OEM drain valve for an air compressor. A drain valve is a small device that is usually located at the bottom of the compressor air receiver. The drain valve can be opened or closed, and this allows water to exit the tank. Water builds up if air is left in the tank for an extended period of time, and if left for too long, it can start to rust out the inside of the tank and the drain valve can become clogged with rust or start to corrode. You should be draining the tank each time you use your air compressor to stop this from happening. This is a very quick and simple repair. Use a wrench to remove the old drain valve, and thread the new one into place by hand.
Fixes these symptoms

Installation Instructions

Steven from SMITHS STA, AL
Wouldn't hold air in tank.
Took old drain valve out and replaced with new one. Read more...
O-ring, Set Of 2 – Part Number: E108513
O-ring, Set Of 2
$28.51
In Stock
Fix Number
FIX12099617
Manufacturer Part Number
E108513
This part includes two OEM replacement O-rings for an air compressor. If these O-rings are missing or damaged, your air compressor will not function as it should. These O-rings create an airtight seal between the pump head and outlet tube, which ensures the correct flow of air through the unit. These O-rings are used to seal the connections at both ends of the tube. Due to their rubber material, they are prone to wear over time, and will require a replacement.
Fixes these symptoms
Watch the install video
VALVE PLATE ASSY – Part Number: N017592SV
VALVE PLATE ASSY
$23.10
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX12517182
Manufacturer Part Number
N017592SV
This is a valve plate for your compressor or generator. This part controls the air flow into the pump. When the air is pumped by the piston, it passes through the valve plate and into the compressor tank. The most common sign of a damaged valve is if your pressure is not building up in the tank. The reeds on the valve plate are usually the first thing to wear out. If you notice visible damage on the reeds you will need to replace this part. This valve includes the plate, and the lower gasket. The head gasket is sold individually.
Fixes these symptoms

Installation Instructions

Ray from Derby, CT
low air pressure
removed head and air tube, reassembled same Read more...
CAP, OIL FILL W/O-RING – Part Number: E100087
CAP, OIL FILL W/O-RING
$15.22
In Stock
★★★★★
★★★★★
2 Reviews
Fix Number
FIX18715722
Manufacturer Part Number
E100087
This is an oil fill cap with a gasket seal attached. It is sold as an individual part and is used in air compressors. It connects to the crank case cover to help contain the oil inside the unit. No tools are required, just twist to secure into place. If your air compressor is leaking oil, or this part is damaged, it will need to be replaced with this genuine OEM replacement part.

Installation Instructions

Wynn from COHASSET, MA
oil fill/ vent broken
unscrewed broken part screwed in new part Read more...
Watch the install video
Ferrule – Part Number: ST085200AV
Ferrule
$6.51
In Stock
Fix Number
FIX10051151
Manufacturer Part Number
ST085200AV
Genuine Campbell Hausfeld replacement part, this item is sold individually. The Ferrule in this case is used on all of the compressors listed below. It is placed inside a Compression Nut of which is on a copper or aluminum tube and then attached to a component of the compressor. It aids in stopping air leaks.
Fixes these symptoms
Watch the install video
Connecting Rod Assembly – Part Number: N036518
Connecting Rod Assembly
$56.02
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10049057
Manufacturer Part Number
N036518
This is a Genuine OEM replacement part designed for use with Air Compressors. This kit Includes: Piston Rod, Compression Ring , Cylinder Sleeve & Bearing. Please note that this kit does not include the valve plate, head gaskets, or any other compressor parts. Replacing this kit you would need a Screwdriver, Hex Key/Allen Wrench and Pliers.
Watch the install video
CLAMP HOSE .250 ID – Part Number: CAC-1206-1
CLAMP HOSE .250 ID
$6.51
On Order
Fix Number
FIX12513333
Manufacturer Part Number
CAC-1206-1
This high-quality OEM metal hose clamp is a part found in air compressors, and is sold individually. This part can be used on multiple parts on the air compressor, so the exact location, and repair may differ. In general, it is used to clamp hoses. For this repair, begin by draining the air out of the tank to remove the pressure placed on the components.
Fixes these symptoms

Installation Instructions

Rick from FRAMINGHAM, MA
Air leakage from hose
I followed the help from a YouTube video. It was for a slightly different model of P-C air compressor, but didn't really matter. This procedure is quite straightforward. Several screws are removed to access the pump-end of the rubber hose. Use The new hose was somewhat longer than the old one, but I didn't try to cut it down. Be sure to crimp the replacement clamps good and snug! Secure all screws and test the compressor. All good! Read more...

Husky Compressor Appliance Types

Popular Husky Compressor Models

View More
+