OEM Husky Lawn Mower Parts & Accessories

CABLE-CONTROL 37.5

$18.74

Fix Number: FIX19305064
Manufacturer Part Number: 946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

Lawn Mower Flanged Lock Nut

$6.51

Fix Number: FIX9095080
Manufacturer Part Number: 712-04065

This lock nut is used for lawn and garden equipment, and is sold individually. This nut resists loosening when it is correctly threaded onto a bolt in your tool. The measurements are: the diameter of the bolt hole is 3/8 inches and the thread count is 16. For instructions on where the lock nut is located in your tool refer to the manual provided by the manufacturer.

Nut-flglk 5/16-18

$6.51

Fix Number: FIX9092936
Manufacturer Part Number: 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Upper Handle

$42.61

Fix Number: FIX16424685
Manufacturer Part Number: 749-05084B-0637

This replacement handle is a genuine OEM sourced part. It is specially manufactured for walk behind and push lawn mowers. Upper handle allows user to control the lawn mower. It is attached to the lower handle assembly that is sold separately. This part is made out of metal and is sold individually. Please note, the control bar, knobs and cables are all sold separately. You will need a wrench to replace this upper handle. • Disconnect the bail bar • Detach the control cable • Remove the bolts and the nuts that secure upper handle • Secure the new handle using the same hardware • Reattach the bar and the control cable

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

Watch the install video

Grass Catcher Frame Assembly

$50.22

★★★★★

4 Reviews

Fix Number: FIX9988561
Manufacturer Part Number: 647-04271-0637

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Craftsman lawn mowers. The grass bag frame supports and hold the grass bag in place, while it is collecting grass clippings. To install or replace the grass bag frame requires no tools. This part is made of metal and is sold individually.

Watch the install video

Lawn Mower Trail Shield

$15.55

★★★★★

3 Reviews

Fix Number: FIX9103444
Manufacturer Part Number: 731-07203

This replacement trail shield is specially designed for use on walk-behind lawn mowers. It is an authentic item that is sourced from original equipment manufacturer and it is sold individually. This plastic trail shield is secured in the back of the deck to protect the user from grass clipping and debris. Please note the hardware to secure it is not included it is sold separately.

Lawn Mower Key

$21.95

Fix Number: FIX9310468
Manufacturer Part Number: 925-1745A

Pin-bow Tie Cotter

$6.51

Fix Number: FIX9096195
Manufacturer Part Number: 714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Fixes these symptoms

Auger will not turn
See more...

Installation Instructions

Laura from CANDLER, NC

The right side of the mowing deck was dragging the ground.

I identified the area and compared it to the opposite side which still had the cotter pin and place. The cotter pin on the right side had been lost in the mowing process. I used pliers to attach the new pin and all is well! Super glad to find a website that carries all parts for my dad's mower. He has dementia and can't remember where the manual is so I was glad to find fix.com. Read more...

Nut-flglk

$6.51

Fix Number: FIX9299574
Manufacturer Part Number: 712-04064

This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torque type lock nut, and it has no temperature or chemical restrictions. This part has a 1/4-inch diameter and 20 thread size.

Axle Asm-rear 11

$46.76

Fix Number: FIX16386134
Manufacturer Part Number: 611-04144B

This authentic component is sourced directly from the original equipment manufacturer. It is specially designed for use with push lawn mowers. It is an identical replacement for a damaged or a missing rear axle assembly that was installed on a new unit. This is the part that the wheels are attached to. Refer to the diagrams of your model for the exact location and the correct installation of this component. Note, it is made of durable metal and is sold individually. You will need a wrench set and a screwdriver to remove the wheels, disconnect the old axle assembly and attach the new part.

Installation Instructions

Ricky from JOLIET, IL

The adjustment lever attached to the rear axel assembly, which is used to raise/lower the rear wheels was broken off.

Removed dust covers, nuts and rear wheels from rear axel assembly. Tipped mower onto side per manufactures instructions. Removed rear axel assembly from slots (standard screwdriver used here to pry). Installed new assembly by reversing the above steps. Read more...

Husky Lawn Mower Parts

Popular Husky Lawn Mower Parts

Installation Instructions

Installation Instructions

Installation Instructions

Husky Lawn Mower Appliance Types

Popular Husky Lawn Mower Models

Husky Lawn Mower Parts

Start With Your Model Number

Popular Husky Lawn Mower Parts

Installation Instructions

Installation Instructions

Installation Instructions

Husky Lawn Mower Appliance Types

Popular Husky Lawn Mower Models