Washer Agitators

★★★★★

★★★★★

20 Reviews

Fix Number

FIX388034

Manufacturer Part Number

80040

Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX334650

Manufacturer Part Number

285811

This is an OEM agitator repair kit that includes an agitator cam, four directional cogs, a bearing, thrust spacer, inner cap seal, and washer. These parts are found inside the agitator auger near the top. This kit is used when the top portion of the agitator is not moving correctly but the bottom part is. The agitator is subjected to a lot of force during the wash cycle, so it is common for this part to wear over time, especially if you are consistently over-loading your washer. If your model has a softener dispenser, it will need to be removed to perform this repair. Agitator grease is recommended for this repair, but is not included in this kit.

Fix Number

FIX334648

Manufacturer Part Number

285809

This is an authentic OEM agitator cam kit for your washing machine. The kit includes a bearing, the cam holder, and four individual cams. You may need to replace the agitator cam if you find your washer is noisy, it shakes and moves, or it will not agitate. To do this repair we find it easiest to remove the agitator and you will need a 7/16 socket to do this. Once the agitator has been removed from the washer, you can remove the old cam kit from the top portion. The four individual cams are inserted into the cam holder, and the bearing holds them all in place. The assembly can be placed back inside the agitator, and then the agitator installed back inside the washer.

Fix Number

FIX1482519

Manufacturer Part Number

WH43X10034

This is an authentic agitator for your washer, responsible for moving clothes inside the tub. Please note, it does not come with the fabric dispenser, so you will need to either transfer the old one to your new agitator or order it separately. While troubleshooting and before ordering this part, we recommend also inspecting the condition of the agitator coupler. For this simple repair, remove the old agitator by pulling it upwards. If it is difficult to remove, try placing straps underneath to pull it out. Lower the new agitator down onto the coupler, making sure it is lined up properly, and then push down on it until it snaps into place.

Fix Number

FIX11748113

Manufacturer Part Number

WPW10074580

The O-Ring is included with this cap. It can be purchased separately as Part #WPW10072840.

★★★★★

★★★★★

1 Review

Fix Number

FIX334562

Manufacturer Part Number

285587

The thrust spacer is a genuine OEM part that is more commonly known as a retainer ring. The spacer is made of white plastic and measures approximately 2.5 inches in diameter. This part is found in between the agitator and the auger in your direct drive washing machine. The space is used to support the auger and secure it on the agitator base. If your washer will not agitate, or is shaking or excessively noisy while running, you may need to replace the ring. Please note that this repair requires dual-action agitator grease, which is not included with this part.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334622

Manufacturer Part Number

285748

This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.

Fix Number

FIX11727882

Manufacturer Part Number

W10836692

This agitator is for washers. Agitator rotates back and forth to move the clothes inside the tub to clean the load. Unplug the washer before installing this part. Wear work gloves to protect your hands.

★★★★★

★★★★★

1 Review

Fix Number

FIX11742049

Manufacturer Part Number

WP3951744

This agitator comes with the 4 agitator dogs (cogs) and top mover. The cap is NOT included with the agitator.

Fix Number

FIX1517844

Manufacturer Part Number

WH49X10042

This genuine OEM part is an agitator coupling kit for your washing machine. Also known as an agitator drive belt, this part is used to connect the transmission drive shaft to the base of the agitator. Over time, the teeth on the coupler will wear out and the part will need to be replaced. Signs that you will need to replace this part include your washing machine making a noisy grinding sound, the washer will not agitate or spin, and it excessively shakes or moves while running. This kit includes a coupler, gasket, and bolt. Please be sure to disconnect the power supply to your washer before beginning this repair.