Roper Washer Agitators

★★★★★

★★★★★

20 Reviews

Fix Number

FIX388034

Manufacturer Part Number

80040

Commonly referred to as dog ears, these agitator directional cogs are manufacturer approved replacement parts that come in a package of 4 and are usually used with direct drive washing machines. We recommend replacing all 4 directional cogs at the same time. The agitator directional cogs reach across the gear teeth in one direction and dig into the gear teeth in the other direction to create the needed agitation. This thrusting motion is what tumbles your clothes during the wash cycle. When the teeth on the outer edge are damaged, the cogs will not engage with the upper agitator, making it impossible to agitate as it should. If your machine makes unusual noises, shakes/moves while operating, or will not spin or drain properly, it may be time to replace them. To access this part, simply remove the softener dispenser and then the agitator cap. You will find them attached to the agitator. Each cog is approximately 1 inch long and made of a durable plastic.

★★★★★

★★★★★

10 Reviews

Fix Number

FIX334650

Manufacturer Part Number

285811

This is an OEM agitator repair kit that includes an agitator cam, four directional cogs, a bearing, thrust spacer, inner cap seal, and washer. These parts are found inside the agitator auger near the top. This kit is used when the top portion of the agitator is not moving correctly but the bottom part is. The agitator is subjected to a lot of force during the wash cycle, so it is common for this part to wear over time, especially if you are consistently over-loading your washer. If your model has a softener dispenser, it will need to be removed to perform this repair. Agitator grease is recommended for this repair, but is not included in this kit.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334557

Manufacturer Part Number

285565

This agitator kit does NOT include the fabric softener dispenser (part 8575076A). That must be ordered separately.

★★★★★

★★★★★

1 Review

Fix Number

FIX11741151

Manufacturer Part Number

WP3347288

This OEM agitator base connects to the auger and helps move clothes during the wash cycle. It rotates to create water movement that loosens dirt and improves cleaning. Replace if the agitator stops moving, cleaning performance drops, or the washer vibrates excessively.

★★★★★

★★★★★

1 Review

Fix Number

FIX334562

Manufacturer Part Number

285587

The thrust spacer is a genuine OEM part that is more commonly known as a retainer ring. The spacer is made of white plastic and measures approximately 2.5 inches in diameter. This part is found in between the agitator and the auger in your direct drive washing machine. The space is used to support the auger and secure it on the agitator base. If your washer will not agitate, or is shaking or excessively noisy while running, you may need to replace the ring. Please note that this repair requires dual-action agitator grease, which is not included with this part.

Fix Number

FIX11727882

Manufacturer Part Number

W10836692

This agitator is for washers. Agitator rotates back and forth to move the clothes inside the tub to clean the load. Unplug the washer before installing this part. Wear work gloves to protect your hands.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX334622

Manufacturer Part Number

285748

This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.

Fix Number

FIX11748740

Manufacturer Part Number

WPW10131112

Fix Number

FIX11741199

Manufacturer Part Number

WP3355758

This is the cap for your agitator.

Fix Number

FIX12731183

Manufacturer Part Number

W11397111

This washplate helps your washer clean clothes better by spinning them through water and detergent. It’s designed to reduce tangling and make sure everything gets a good wash. If your washer isn’t agitating or cleaning well, this part might be the fix. It’s about 13 inches wide and fits many Whirlpool, Maytag, and KitchenAid models. Just remove the old one and bolt this one in place.