Roper Washer Transmissions and Clutches

★★★★★

★★★★★

2 Reviews

Fix Number

FIX6012095

Manufacturer Part Number

W10528947

The drive hub connects the basket of your washer to the transmission shaft, which in turn allows the basket to spin. If your washer will not agitate, spins slowly, or is excessively noisy, it may require a new drive hub assembly. This genuine OEM kit comes with a new hub and a fork holder. To replace this part, you will need to remove the agitator from the tub to expose the hub assembly. Use a flat blade screwdriver to remove the fork shaped holder, and then remove the screws holding the hub assembly to the transmission shaft. Place the new hub onto the shaft, and rotate the washer tub to line up the holes. Once lined up, drill the screws back into place. Please note that this kit does not come with replacement screws, so you will need to reuse the ones from the old hub. The new fork holder is then put through the slotted opening, using a small hammer to tap it into place. Once you have installed the new part, be sure to follow the instructions on the pamphlet provided with the hub to calibrate your washer.

★★★★★

★★★★★

1 Review

Fix Number

FIX334641

Manufacturer Part Number

285785

This is a genuine OEM replacement clutch assembly for your washing machine. A clutch assembly, also known as a clutch or a washer clutch, is responsible for spinning the tub during the spin cycle. If the clutch becomes worn and is no longer operating properly, your clothes will remain soaked after the cycle is finished. Some other signs it is time to replace the clutch is if your washer is noisy while running, there is a burning smell, or the machine is shaking excessively. This kit comes with the clutch, brake cam driver, spring, retaining ring, and a nylon anti-rattle clip. Before beginning this repair, be sure to disconnect the power and water supply to your machine. Depending on your washer model, you may need an additional person to help lower the machine onto its back, as access to the drive shaft to change the clutch assembly may be easiest through the bottom of the appliance.

★★★★★

★★★★★

1 Review

Fix Number

FIX11769864

Manufacturer Part Number

W10913953

This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer transmission during the different phases of the wash cycle. This allows the washer to switch between agitating and spinning modes. Signs of a faulty shift actuator include the washer failing to agitate or spin, incomplete cycles where the washer gets stuck in one phase, or unusual noises during operation

★★★★★

★★★★★

1 Review

Fix Number

FIX16220910

Manufacturer Part Number

W11454372

This includes the Tub Seal

★★★★★

★★★★★

1 Review

Fix Number

FIX11747977

Manufacturer Part Number

WPW10006355

This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.

Fix Number

FIX341974

Manufacturer Part Number

3360629

This is used in your direct drive washer that has a neutral drain.

Fix Number

FIX16220913

Manufacturer Part Number

W11454741

This gear case is for washers. The Gear case drives the agitator and spins the basket in the washer. Unplug the washer before installing this part. Wear work gloves to protect your hands.

Fix Number

FIX11723156

Manufacturer Part Number

W10820043

This basket drive assembly is for washers. Basket drive assembly sits on top of the transmission shaft and houses the spin basket brake mechanism. The basket drive spins to rotate the basket during the spin cycle.

Fix Number

FIX334642

Manufacturer Part Number

285790

This kit comes with springs, hardware, and brake lining.

Fix Number

FIX334528

Manufacturer Part Number

285438

This assembly comes with two brake shoes.