Maytag Washer Dryer Combo Hardware

Maytag Appliance Parts
Shop By Part Type

Popular Maytag Washer Dryer Combo Hardware

$13.44
In Stock
Roller Support Tri-Ring
Fix Number FIX11755850
Manufacturer Part Number WPW10512946
This small but mighty OEM piece is called a tri-ring and is used to support the drum roller shaft and the idler pulley shaft in your dryer. It helps to provide a tight seal between components by evenly distributing pressure. The part is triangular in shape, and less than an inch in size. Overtime it can become brittle or compressed, which can lead to a noisy tumbling cycle, or your dryer not tumbling at all. The tri-ring itself is simple to replace, simply slip off the damaged one and slip on the new. However, to access the drum roller or idler pulley, you will need to remove the front panel and drum of your dryer. This may require tools like a Phillips screwdriver, a quarter inch nut driver, putty knife, a small flat blade screwdriver, and a pair of needle nose pliers depending on your model. Ensure that the power is disconnected before beginning your repair.
Fixes these symptoms
$7.48
In Stock
Agitator Bolt
Fix Number FIX11741866
Manufacturer Part Number WP358237
This bolt is a genuine OEM replacement part, used to secure the agitator in your washing machine. Overtime the bolt can become worn out due to the vibrations of the washer, and will need to be replaced. The size of the screw head is 7/16 inch, so you will need the appropriately sized socket to complete this repair. The new bolt comes with a rubber gasket and a threaded sealant.
Fixes these symptoms
$40.60
In Stock
Igniter Kit
★★★★★
★★★★★
(1)
Fix Number FIX334180
Manufacturer Part Number 279311
This is a genuine OEM replacement igniter kit for your gas-heated clothes dryer. The silicon carbide igniter is used to light the gas that creates the heat in order to dry your clothes. If your dryer is not heating, takes a long time to dry clothes, or has low heat you may want to consider replacing your igniter. This kit can be used to replace both round and flat igniters, and comes with a 3-inch flat igniter, bracket, 4-inch wire lead, and the plug. Before beginning this repair, please ensure that the power and gas is disconnected from the range. As the igniter is located within the burner assembly, you will need a variety of tools to complete the installation. These tools include a putty knife, a small flat blade screwdriver, a 5/16 nut driver, and a 5/16 socket with a ratchet. This part should be handled with care, as the igniter is very fragile.
Fixes these symptoms
  • No heat or not enough heat
  • Takes too long to dry
  • Will Not Start
  • See more...
$6.92
In Stock
Retaining Ring
Fix Number FIX11746909
Manufacturer Part Number WP9703438
Sometimes referred to as a retaining clip, the retaining ring is used to hold the drum support roller onto the shaft in your dryer. The clip may need to be replaced if you find that your dryer is noisy while tumbling or will not tumble at all. The retaining clip can also be used with stand mixers, to hold the pinion gear to the agitator shaft. This genuine OEM part is made entirely out of metal and measures approximately half an inch in diameter.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
$13.35
In Stock
Idler Pulley Shaft Washer
★★★★★
★★★★★
(1)
Fix Number FIX11757538
Manufacturer Part Number WPY312527
This idler pulley shaft washer is used with many clothes dryers. It is less than an inch long, and it is black in color.
Fixes these symptoms
$6.68
In Stock
Suspension Spring Retainer
Fix Number FIX11749057
Manufacturer Part Number WPW10145155
This is a replacement suspension spring retainer for your washer. The retainer holds the suspension spring in place while the washer is operating. If you notice movement, or an unusual noise or shaking of your washer when it is in use, it could mean that the suspension spring has been disconnected because of a broken or missing spring retainer. You will find the suspension spring retainer at the bottom of the tub assembly. To replace the retainer, use a pair of pliers to disconnect the suspension spring from the chassis mount to relieve the tension. Then, remove the spring from the retaining clip, and remove the retaining clip from the bottom of the washer. Attach the new retaining clip to the bottom of the washer, reattach the spring, and stretch it slightly so it can connect to the chassis. This part is sold individually.
Fixes these symptoms
$12.90
In Stock
Single Front Panel Cip
Fix Number FIX11731288
Manufacturer Part Number W10854425
This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.
Fixes these symptoms
$7.76
In Stock
Cover Screw
Fix Number FIX11740701
Manufacturer Part Number WP308685
This is a multi-use cover screw. It fits appliances such as dryers, ranges, washers, dishwashers, refrigerators, air conditioners, washer dryer combos, freezers, wall ovens, microwaves, dehumidifiers, cooktops, trash compactors, grills, and ice makers. *Please note: This part is sold individually.
$13.36
In Stock
Drum Roller Shaft Washer
Fix Number FIX11740748
Manufacturer Part Number WP312535
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
Fixes these symptoms
$7.76
In Stock
Screw - 10-16 x 1
Fix Number FIX11741409
Manufacturer Part Number WP3387230
This is a multi-use screw mostly used in dryers. It has a diameter of #10, length of one inch, and thread size of 16. Remember to follow safety practices and instructions provided in the manufacturer manual. *Please note: this screw is sold separately.

Related Parts