Crosley Dryer Fuses

Dryer Thermal Fuse

★★★★★

★★★★★

15 Reviews

The dryer thermal fuse, also sometimes referred to as the thermal cut off or temperature fuse, is a 2 by 1/2-inch, white, plastic safety mechanism that halts the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is intended to manage. This can be caused by the heating element shorting, a regulating thermostat or thermistor failure, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16-inch terminals. While performing this repair, we recommend checking to make sure all vents are cleared and vacuumed. This OEM part is sold individually.

Thermal Cut-Off Kit

★★★★★

★★★★★

8 Reviews

This thermal cut-off kit is for a dryer and is sourced directly from the manufacturer. The thermal cut-off is a safety mechanism that is designed to trip if your dryer is at risk of overheating, to prevent further damage. It may need to be replaced if your washer is no longer heating properly. This is a one-time fuse, meaning if it trips, it needs to be replaced immediately. A common reason for this part to fail is if the heater housing is not receiving proper airflow, normally caused by an obstruction in the exhaust vent, a clogged lint screen, or a broken blower wheel. This kit includes 1 high-limit thermostat with a limit of 250 degrees Fahrenheit, 1 thermal cut-off fuse with a limit of 309 degrees Fahrenheit, jumper wires and new female spade terminals. These components are attached to the heater housing.

Thermal Limiter - Limit 220 This thermal fuse limiter is used in dryers to monitor the temperature and make sure it does not overheat. The thermal fuse has a limit of 220 degrees Fahrenheit before the heating element and power are cut off. If your thermal fuse has blown or is damaged then your dryer will not start, can over heat, or take too long to dry. It is important to replace the fuse to solve the above problems. For this repair, you will need a Philips screwdriver, putty knife, and a needle nose plier. As a safety precaution, remember to unplug dryer from power source to avoid electrocution when installing this part. Refer to the manual provided by the manufacturer for further instructions.

High Limit Thermostat and Thermal Cut-Off Kit This thermal cut-off kit includes a genuine OEM replacement high limit thermostat and a fuse. The thermostat is a safety device used to prevent the dryer from overheating, and the fuse serves as a backup. If the temperature in your dryer gets above the thermostat, the fuse will blow. Once the fuse has tripped, it will need to be replaced. If your dryer will not start, gets too hot, shuts off too soon, or there is no heat, you may need to replace these components. Please be sure to disconnect the power supply to your dryer before beginning this repair, as you will be working with electrical components.

High Limit Thermal Fuse

★★★★★

★★★★★

2 Reviews

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.

Thermal Fuse

High Limit Kit

★★★★★

★★★★★

3 Reviews

This kit comes with three separate thermal fuses and is usually used with clothes dryers that have a fan mounted on the motor shaft. Included within this kit is the high limit (Limit: 258) the gas high limit (Limit: 240) and the gas and electric high limit thermostat (Limit: 300).

Thermal Cut-Off with High Limit Thermostat The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element.

Thermal Fuse

Thermal Fuse