Kenmore Dishwasher Caps and Lids

Kenmore Appliance Parts

Popular Kenmore Dishwasher Caps and Lids

Stop Clip
$7.28
In Stock
Fix Number
FIX11770481
Manufacturer Part Number
5304506510
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.
Rinse Aid Cap
$19.97
In Stock
Fix Number
FIX421128
Manufacturer Part Number
154388801
This is a replacement cap for the detergent/rinse aid dispenser. If the rinse aid cap is damaged or missing, you may notice too much rinse aid in the dishwasher. The cap simply screws into the dispenser, so if your cap is damaged you can simply screw it out, then screw in the new one. The rinse aid cap is approximately 2 inches in diameter and is sold individually. This is an OEM part, directly from the manufacturer.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Fix Number
FIX11746426
Manufacturer Part Number
WP8558307
This part includes one OEM rinse aid cap (also known as a dispenser cap), and its purpose is to cover the rinse aid dispenser located on the dishwasher door. Please note that this manufacturer-approved cap has a diameter of 1.42 inches. If the original cap is bigger than that, you may need to replace the entire dispenser assembly. This part is commonly replaced because the dishwasher is not properly dispensing detergent, or it is leaking detergent. Be sure to assess the condition of the rinse aid cap as well as the gasket. This rinse aid cap comes with a gasket, so the old one can be tossed. For this simple DIY repair, open the dishwasher door, turn the old cap a quarter-turn counterclockwise to remove it. Place the new cap in its place and secure it by turning it a quarter-turn clockwise.
Fixes these symptoms
  • Door latch failure
  • Leaking
  • Not cleaning dishes properly
  • See more...
LID
$17.42
In Stock
Fix Number
FIX8727344
Manufacturer Part Number
00611322
Fixes these symptoms
Tub Cap
$15.52
In Stock
Fix Number
FIX11703426
Manufacturer Part Number
W10795980
The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.
Fixes these symptoms
Rinse Aid Cap
$11.12
In Stock
Fix Number
FIX11741341
Manufacturer Part Number
WP3378134
This cap does not require the use of a o-ring seal.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
LID
$18.67
In Stock
Fix Number
FIX8697157
Manufacturer Part Number
00166623
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Leaking
  • See more...
Rinse Aid Fill Cap
$18.40
In Stock
Fix Number
FIX2351824
Manufacturer Part Number
WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Rinse Aid Cap
$18.83
In Stock
Fix Number
FIX11746567
Manufacturer Part Number
WP8564929
This rinse aid cap or fill cap is for your dishwasher and it screws into the jet dry dispenser. Sometimes the cap can become loose and fall out, which can cause it to melt from the heater. If your cap is damaged or missing, this is the part you will need to replace it. It is made of white plastic and is a little more than an inch in diameter. This rinse aid cap is sold individually.
Fixes these symptoms
  • Leaking
  • Not cleaning dishes properly
  • Not drying dishes properly
  • See more...
Dispenser Cap
$23.53
In Stock
Fix Number
FIX11746156
Manufacturer Part Number
WP8533380
This is the cap for your rinse aid dispenser.
Fixes these symptoms

Related Kenmore Dishwasher Parts