LG Washer Parts

Start With Your Model Number

Need help finding your model number?
Find Parts Fast
Guaranteed Fit
Repair Videos
Fix.com search
LG Appliance Parts
Shop By Appliance Type Shop By Part Type

Popular LG Washer Parts

Door Boot Seal – Part Number: MDS47123602
Door Boot Seal
$114.57
In Stock
Fix Number
FIX3535210
Manufacturer Part Number
MDS47123602
This flexible gasket seals the door on your LG or Kenmore front-load washer to keep water from leaking during cycles. If you’re seeing puddles, smelling mildew, or noticing moisture around the door, replacing the gasket can help. It’s made from durable material and fits many models—just check your washer’s model number to be sure.
Fixes these symptoms
Watch the install video
Dryer Drum Belt – Part Number: 4400EL2001F
Dryer Drum Belt
$37.35
In Stock
Fix Number
FIX11705916
Manufacturer Part Number
4400EL2001F
If the drum in your dryer will not tumble, or it is noisy while operating, there may be an issue with the drum belt. The belt is found looped around the dryer drum, a tension pulley, and a motor pulley and is used to rotate the drum so that your laundry tumbles. Over time the belt can become stretched out, or it becomes brittle and will snap. If this happens the belt will need to be replaced. If you need a replacement, this is a genuine OEM dryer drum belt. The belt measures about a quarter inch wide, and has four ribs and three groves. Please be sure to disconnect the power supply to your dryer before beginning this repair.
Fixes these symptoms

Installation Instructions

John from Seaford, NY
Noisy Dryer
I took the dryer apart and found the forward drum support roller was wobbling. I decided to replace all 4 rollers and the drive belt. Parts arrived within 3 days and the install took less than an hour. I didn't notice any lubricant on the new roller shafts, so I took them apart and applied a very thin film of synthetic grease. I also did the same to the tensioning roller assembly. The install worked out fine. Read more...
Washer Water Inlet Valve – Part Number: AJU75152601
Washer Water Inlet Valve
$154.80
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX12374721
Manufacturer Part Number
AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Fixes these symptoms
  • Leaking
  • No hot or cold water
  • Water Filling Issues
  • See more...

Installation Instructions

Joy from HALIFAX, PA
My washer would not stop filling with water even when turned off
Unplugged it. Took back panel off. Unscrewed valve cover. Unhooked hoses. Replaced inlet valve. Replaced hoses. Replaced cover. Replaced panel Read more...
SENSOR ASSEMBLY – Part Number: 6501KW2002B
SENSOR ASSEMBLY
$58.25
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX16556422
Manufacturer Part Number
6501KW2002B
The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code on your control display, the sensor has failed and will need to be replaced. This is a genuine OEM part sourced directly from the manufacturer. Please remember to disconnect the power to your washer before starting your repair.
Fixes these symptoms
  • Spinning Issues
  • Spins slowly
  • Will not agitate
  • See more...

Installation Instructions

John from LAKE GROVE, NY
pump was blow and the sensor broke
My friend is a handy man and did everything for me but i will definitely use you again. Read more...
Watch the install video
Door Lock Assembly – Part Number: EBF49827801
Door Lock Assembly
$82.45
In Stock
Fix Number
FIX3533609
Manufacturer Part Number
EBF49827801
The door lock assembly is a genuine OEM part for your washing machine. This part informs the washer that the door is closed and locked in place, which allows the machine to start its cycle. If you are not able to open or close the door, or the washer will not start, the door lock assembly may need to be replaced. This can happen if the switch has shorted out, which will prevent the latch from locking. Before beginning this repair, please be sure to disconnect the power supply to your washer. You will need a Phillips screwdriver in order to replace this part.
Fixes these symptoms
  • Lid or door won’t close
  • Locking Issues
  • Will Not Start
  • See more...

Installation Instructions

Edward from St Augustine, FL
Door Latch malfunction
I basically followed the video instructions which made it very easy to understand and follow. The most difficult aspect was disconnection the wire harness in a small space. Read more...
Lint Filter – Part Number: ADQ73373201
Lint Filter
$78.55
In Stock
Fix Number
FIX7787727
Manufacturer Part Number
ADQ73373201
This lint filter assembly for your dryer catches lint and debris from your clothes. You can find it near the door. It helps keep the air flowing properly and stops lint from blocking the exhaust ducts. If it is broken or clogged, your clothes will take more time to dry, and there is a risk your dryer could overheat, leading to a fire. This is a genuine replacement part from the original manufacturer and is sold individually.
Magnetic Door Plunger – Part Number: AGM73610701
Magnetic Door Plunger
$19.63
In Stock
★★★★★
★★★★★
3 Reviews
Fix Number
FIX3618292
Manufacturer Part Number
AGM73610701
This magnetic door plunger is a genuine replacement component designed to keep the washing machine door slightly ajar when not in use. By allowing air circulation, it helps the inner door and tub seal dry thoroughly, reducing the risk of mold and mildew buildup. If the washer door fails to close properly, the plunger may be damaged and require replacement. The part includes a plastic housing and spring mechanism, and installs easily by aligning the tabs with the slots on the inner door panel and snapping it into place. No tools are required, but power should be disconnected before installation. Sold individually
Fixes these symptoms
  • Leaking
  • Lid or door won’t close
  • Locking Issues
  • See more...

Installation Instructions

DEREK from Fishers, IN
Plunger was broken
Very simple fix, line clips with door and push in. Read more...
Watch the install video
Washing Machine Drain Pump – Part Number: 4681EA2001T
Washing Machine Drain Pump
$65.37
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX3579318
Manufacturer Part Number
4681EA2001T
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it can cause the washer to not drain properly. Keep in mind that the pump casing is sold separately. This repair is rated medium-difficulty and can vary depending on the model. For this repair you will need a Philips screwdriver, a small flat blade screwdriver, needle nose pliers, and slip joint pliers. Do not forget to disconnect the power before you begin this repair. In general, this repair can be started by removing the top of the washer followed by the front panel. Moving down the front of the appliance, remove the door, latch, tub gasket, and drainer cover. The drain hoses and clip will need to be disconnected from under the drain assembly. To install the new pump motor, reassemble parts in the reverse order. We recommend taking photos while disassembling and keeping screws and parts neatly organized.
Fixes these symptoms
  • Draining Issues
  • Engine runs but does not pump water
  • Leaking
  • See more...

Installation Instructions

Michael from Oconomowoc, WI
Water was not draining from wash tub. A code "0E" was showing on the display
Your Youtube video describes the repair perfectly. I'll add: Be careful when removing and placing the control panel on top of the Washer. Once removed, my panel had a wire harness with a zip tied. I cut the zip tie to allow enough slack to lay the panel on top of the washer. No need to disconnect any wires (I put a new zip tie on upon reassembly.) Be careful when removing the retention ring around the Rubber Boot, takes a little finesse, but not too difficult, Don't use a sharp object as you don't want to cut the boot. Make sure the boot is properly seated and the retention ring is securely in place upon reassembly. When removing the old pump my model has the pump held in place with 2x screws (easy to get at from the front) and also slides onto a plastic foot that has a "tab" that needs to be depressed to slide the motor out. You can't see the foot or tab from the front of the washer, as its hidden behind the pump, but fish around with your hand and you'll feel the tab..hold it down and the pump will slide towards the back of the Washer. Thanks, $60 bucks and couple hours was way better than a new $700 Washer. Read more...
LOCKER,HOOK – Part Number: MFG63099101
LOCKER,HOOK
$48.35
In Stock
Fix Number
FIX8752721
Manufacturer Part Number
MFG63099101
Fixes these symptoms
  • Lid or door won’t close
  • Locking Issues
  • Will Not Start
  • See more...
GASKET – Part Number: MDS66290801
GASKET
$154.80
In Stock
Fix Number
FIX12590532
Manufacturer Part Number
MDS66290801
This rubber gasket seals the door on your LG front-load washer to keep water from leaking out during cycles. If you’re noticing puddles, mildew smells, or moisture around the door, replacing the gasket can help. It’s made to last and also helps reduce vibration while your washer runs. Fits many LG models.
Fixes these symptoms

LG Washer Appliance Types

Related LG Washer Parts

Popular LG Washer Models

View More
+