Jenn-Air Washer Parts

Fix Number: FIX11757492
Manufacturer Part Number: WPY055980

This is replacement high temperature adhesive for your washer and dryer. It is designed to hold objects together, and will not disintegrate at a high temperature. This is a 2-ounce tube of adhesive that is sold individually. This is an OEM product sourced directly from the manufacturer.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Ralph from Alexandria, OH

Grinding , drum flopping , .....Noise !

I won't go into all the details of the repairs .....The videos this company provides are A+++.. Some would say I would have been better off purchasing a New dryer ...LOL if I had to use a appliance repair man for this job ...Probably ...but ...using this site certified parts , and using the easy to follow instruction videos ....It was truly a very easy repair . I spent more time getting everything perfectly clean inside the dryer housing ,and letting the high temp adhesive cure than I did actually installing the parts.I can't recommend this company or the parts more ...Just take your time with removal , cleaning , and installation ....Patience !Excellent ...parts quality , shipping speed , and video installation instructions !!!! My dryer now works and SOUNDS like a new dryer ....Thank you ! Read more...

Drive Belt - 51 inches long

$10.98

Fix Number: FIX11738882
Manufacturer Part Number: WP21352320

This is a V-style drive belt that measures approximately 51-inches long and 3/8-inches wide. This part connects the drive motor to the drive system in the washer to turn the basket. It is prone to wear with time and require replacement. Some common signs that the drive belt may be worn is if the motor continues to run, but the washer is not agitating, spinning, or draining. This part is sold individually and is OEM authorized.

Fixes these symptoms

Burning smell
Leaking
Spinning Issues
See more...

Installation Instructions

Sharon from Rowlett, TX

The pulley from the motor broke. It cause the belt to stretch.

A burn smell was coming out from the bottom of the washer. I followed the instructions in the video. It was so easy. I have to add that I am a 45 year old woman. If I can do it anybody can! Thank you so much you saved me about 300 hundred dollars. My husband wanted to buy a new one. Read more...

Snubber Ring

$13.11

Fix Number: FIX11738845
Manufacturer Part Number: WP21002026

This snubber ring fits washers and is located between the leg and dome assembly. The ring has a diameter of 9 inches. It is used to reduce noise and vibration for stability when the washer is operating. If your washer shakes a lot and makes loud noises, then it is best to replace this part to solve your problem. The tools required for this repair are: short flathead screwdriver, flathead screwdriver, Philips screwdriver, 1/4 inch nut driver, 5/16 inch nut driver, 3/8 nut driver, ratchet with extension, putty knife, locking pliers, slip joint pliers, and 3/8 inch socket.

Fixes these symptoms

Shaking and Moving
Spins slowly
Will not agitate
See more...

Installation Instructions

Brandon from Keller, TX

Washer would run and agitate but would not spin.

Prior to the spin cycle not working, the washer would make a loud screeching noise when the spin cycle would stop. I wasn't sure if there was a problem with the break rotor or some bearing was out. Due to the washer's age, I decided to go ahead and replace the pulley, brake rotor, motor pivot spring and snubber ring components.
I began by unplugging the unit first, securing the lid with duct tape and laying the washer on its front face. I removed the belt and transmission pulley per instructions contained in the replacement kit. Mainly consists of popping the "E" ring off with a screwdriver. Once the pulley was off, I stood the washer upright and to access and remove tub. Having the tub out made it easier to compress the brake spring when re-attaching the brake stator. Removing the tub is easy, I just popped off the tub cover and tilted the tub around to ease the tension and remove the bottom springs with pliers (this may require an assistant). With the tub removed, I turned it over to remove the brake stator. USE CAUTION WHEN REMOVING THE BRAKE STATOR. A 200 LB BRAKE SPRING IS UNDER IT AND IS UNDER TENSION. With the new brake rotor and brake stator secured, I replaced the snubber ring and motor pivot spring. I put it all back together in reverse order and it spun like a top, is quieter and stops on a dime! Read more...

Transmission Pulley and Bearing Kit

$69.83

Fix Number: FIX2003651
Manufacturer Part Number: 12002213

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.

Fixes these symptoms

Burning smell
Spinning Issues
Spins slowly
See more...

Installation Instructions

Ralph from Oakland, CA

Pump had stop displacing water at spin cycle

Facing washer placed it on right side exposing underneath. Pump and transmission bearing items are accessible from this position. Followed step by step instructions contained with each part. Placed unit upright,supplied power and ran smallest allowed cycle to test. Unit works like new. Actually spin drys better,dryer clothes which works our older dryer less. Great tune-up and should give us several more years of service. Read more...

Lid Hinge

$11.18

Fix Number: FIX11741780
Manufacturer Part Number: WP35-2044

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

Fixes these symptoms

Lid or door won’t close
Will Not Start
See more...

Installation Instructions

Timothy from Woodhaven, MI

Washer pump was broken, making loud continuous noise.

First, make the back of the washer accessable. Second, remove 4 screws holding the plate cover in left rear of washer. Third, use adjustable pliers to remove both hoses. Fourth, use a 10mm socket, and remove the three hold down screws at the base of the water pump. The belt tension will release automatically, when the pump is unbolted. Fifth, reverse same steps. Last, tip the washer forward, and place belt on the transmission pulley and the motor pulley. The motor itself is adjustable with spring tension, allowing you to move the motor itself, while placing the belt on the water pump pulley. When you allow the spring tension of the motor to spring back in place, your belt will be tight. Place water pump cover (access panel) back in place. Your washer is ready to be used. Read more...

Hose Clamp

$11.80

Fix Number: FIX11743008
Manufacturer Part Number: WP596669

This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Albert from Unadilla, NY

noticed water was leaking in front of washer-right before we were leaving for vacation

Upon returning from vacation, we needed to do laundry-so I put some plastic under the washer and we did a load. The water was leaking from the seam between the lid and the back panel on the side with the hot and cold water connections- not the front. I removed two screws from the front bottom panel and two screws from the underside of the lid.Turning the washer on showed the leak was coming from the injection valve( it was brittle from age). The rubber injection valve was replaced and installed( using a little liquid soap to help the rubber hose to slip over the rubber injection valve) with a new clamp. The leak was fixed. Read more...

Lid Hinge Pin

$22.28

Fix Number: FIX11741781
Manufacturer Part Number: WP35-2045

This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.

Fixes these symptoms

Lid or door won’t close
Will Not Start
See more...

Installation Instructions

Timothy from Woodhaven, MI

Washer pump was broken, making loud continuous noise.

First, make the back of the washer accessable. Second, remove 4 screws holding the plate cover in left rear of washer. Third, use adjustable pliers to remove both hoses. Fourth, use a 10mm socket, and remove the three hold down screws at the base of the water pump. The belt tension will release automatically, when the pump is unbolted. Fifth, reverse same steps. Last, tip the washer forward, and place belt on the transmission pulley and the motor pulley. The motor itself is adjustable with spring tension, allowing you to move the motor itself, while placing the belt on the water pump pulley. When you allow the spring tension of the motor to spring back in place, your belt will be tight. Place water pump cover (access panel) back in place. Your washer is ready to be used. Read more...

Tub Bearing Kit

$55.59

Fix Number: FIX2347235
Manufacturer Part Number: 6-2040130

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Fixes these symptoms

Leaking
Will not agitate
See more...

Installation Instructions

Deborah from Earlsboro, OK

Washer suddenly leakedr.

Upon removing the front cover, I could see that the bottom of the outer tub, just above the transmission had water around it. Based on the age of the machine, I went ahead and replaced the tub bearing also.I followed the repair videos. The tub seal kit video had a tub with the plastic tub cover like my model, and the tub bearing kit video used a older model machine. Both videos were EXCELLENT! If you need a part very quickly though, be sure to pay extra for the guaranteed 2-3 day shipping. The website stated that most parts only take 2 days to be delivered. Mine took a week. You will also need to order the spanner wrench; luckily we had one from servicing a family members machine several years ago. Read more...

Drain Pump with Pulley

$84.63