OEM Maytag Washer Transmission Pulley and Bearing Kit [12002213] | Ships Today | Fix.com
Transmission Pulley and Bearing Kit – Part Number: 12002213
Transmission Pulley and Bearing Kit – Part Number: 12002213 Transmission Pulley and Bearing Kit – Part Number: 12002213 https://fixcom.azureedge.net/Schematics/Maytag/48342.gif

Transmission Pulley and Bearing Kit

Your Price
$58.71

Fix Number: FIX2003651

Manufacturer #: 12002213

Manufactured by: Whirlpool

Get this part fast. Average delivery time via standard shipping: 1.8 days.

Part description

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.

Works with the following brands

Maytag, Norge, Admiral, Magic Chef, Crosley, Amana, Hoover, Jenn-Air, International

Works with the following products

Washer

Fixes the following symptoms

Pumps but will not spin | Noisy | Spins slowly | Will not agitate

Videos For installing this part.

Installation Instructions Provided by Fix customers like you.

Average Repair Rating: 3.1 / 5.0, 19 reviews
>
<
Customer:
Ralph from Oakland, CA
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Pump had stop displacing water at spin cycle
Facing washer placed it on right side exposing underneath. Pump and transmission bearing items are accessible from this position. Followed step by step instructions contained with each part. Placed unit upright,supplied power and ran smallest allowed cycle to test. Unit works like new. Actually spin drys better,dryer clothes which works our older dryer less. Great tune-up and should give us several more years of service.
5 of 5 people found these instructions helpful

Were these instructions helpful?   

Customer:
Brandon from Keller, TX
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Washer would run and agitate but would not spin.
Prior to the spin cycle not working, the washer would make a loud screeching noise when the spin cycle would stop. I wasn't sure if there was a problem with the break rotor or some bearing was out. Due to the washer's age, I decided to go ahead and replace the pulley, brake rotor, motor pivot spring and snubber ring components.
I began by unplugging the unit first, securing the lid with duct tape and laying the washer on its front face. I removed the belt and transmission pulley per instructions contained in the replacement kit. Mainly consists of popping the "E" ring off with a screwdriver. Once the pulley was off, I stood the washer upright and to access and remove tub. Having the tub out made it easier to compress the brake spring when re-attaching the brake stator. Removing the tub is easy, I just popped off the tub cover and tilted the tub around to ease the tension and remove the bottom springs with pliers (this may require an assistant). With the tub removed, I turned it over to remove the brake stator. USE CAUTION WHEN REMOVING THE BRAKE STATOR. A 200 LB BRAKE SPRING IS UNDER IT AND IS UNDER TENSION. With the new brake rotor and brake stator secured, I replaced the snubber ring and motor pivot spring. I put it all back together in reverse order and it spun like a top, is quieter and stops on a dime!
1 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
John from Sac City, IA
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
It would agitate slowly and pump. It would only spin about 50% of the time. On and off.
I followed the instructions to a tee!!!
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Samuel from Garrison, ND
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Loud grinding noise during spin cycle.
Just watch the video . The video is superior to the written instructions included with the parts. The parts are perfect, work just like the video indicates. The written instructions tell you to put everything together and then tells you how two parts should have been put together before they were installed. Also, to lube certain parts, after you have put it all together. So, read the instructions but pay attention to the video. Also the video is WAY better at explaining how to adjust the cams, which is dead simple, but hard to understand in the written instructions. Was very happy with how easy the job was overall, took as much time to unhook and hook the machine back up as it did to actually repair it.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Diana from ShowLow, AZ
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Noisy maching coming from the lower elements
I pulled the machine away from the wall, just enough to lean it back far enough to see the parts at the bottom of the unit. I rolled the belt from the big pulley, popped the dust cover from that pulley, removed the retainer clip, and the parts practically fell to a paper towel. replace them in reverse without any problem. Although I unplugged the machine, I did not remove the water hoses or drain line as sufficient room was available with the machine leaned against the wall.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Gary from Statesville, NC
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Tub would not spin
Removed belt, clip, pulley and washers. Installed new pulley, greased, installed washer, clip and checked alignment. Reinstalled belt and test machine. Everything worked. Easy repair. Thanks for the video on how to.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Lou from Saugerties, NY
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Washer would not spin dry
Reviewed others experiences, reviewed the video, read the written instructions. Would have only taken less than 1/2 hour, but I had a problem getting the thin washer and "e" clip on. I ended up just putting on clip without washer but intend to go back at it in 2 weeks or so. Parts solved the problem and the quick shipping was outstanding !
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Gregory from Denver, CO
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Wrench (Adjustable)
Bad thrust bearing
My tub wouldn't spin fast enough to get the water out of my clothes. The repair guy wanted $500 to replace my thrust bearing and snubber ring. I got the parts and fixed it myself in about an hour. The snubber ring didn't actually need to be replaced. The thrust bearing is an easy job. The only tricky part is the e clip. I was able to take it off and put it back on pretty easily with vice grips and a screwdriver used to fully extend the spindle. Washer works perfectly now.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Jimmy from Flat Rock, MI
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Drum not spinning but pumping out water
Washer Thrust Bearing Kit (part #12002213) This is a complete repair kit. that takes about 30 minutes.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Andew from Antelope, CA
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Tub would weakly spin in rinse/spin cycle
Followed the two recommendation; purchased and installed belt and Transmission Pulley and Bearing Kit. Still had the problem after changing out. I believe it may be a brake or transmission problem.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Nicholas from Queens Village, NY
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Machine would not spin during rinse cycle.
Had to replace the thrust bearing. Tilted machine on its back and removed the C clip that holds the bearing and drive pulley all together. Had to make sure the shaft was completely extended in the down position otherwise all the parts wouldn't all fit back on. Trickiest part was to figure out how the belt goes back on. Turns out it is very simple... just walk it back on to the drive pulley with a screwdriver as your turning the pulley.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Jim from Fountain Valley, CA
Parts Used:
  • Transmission Pulley and Bearing Kit
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Washing machine would agitate & pump, but would not spin.
I followed the on-line video which made the installation much simpler than trying to follow the written instructions.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Gerald from Broomfield, CO
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Slow spin and clicking sound
Purchase new washer it was the transmission that was clicking, finally froze up when I got the spin cycle to run like new. Also the snubber ring and springs where replaced that made the spin balance get back to new. Thanks for the videos they where a great help.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Thomas from Yale, MI
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Water drained but it would not spin
I followed the supplied instructions and watched the video. I have told several people about this site. It is a great place to buy repair parts with great online support. The only tricky part was making sure you used the right shims to make the described adjustment. but the instructions were good so I knew what to do.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

Customer:
Veeda from Fort Wayne, IN
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Washer would not spin
installed the pulley and bearing kit purchased through this site and install according to the video. Remove the cap the E clamp, with the aid of a hammer and a flat head screwdriver, the washers and the module. My washer had more washers than what was listed on the video and a different type of washer behind the module, but I put everything together as the video stated, but had a harder time putting the E clamp on, so I used the help of light taps with a hammer and the flat head screw driver. This can be tricky, so be careful not to damage the clamp. In all it took me 20 minutes, and everything worked perfectly. Good for an older woman. If I can do anyone can. Thanks for the videos.
0 of 1 people found these instructions helpful

Were these instructions helpful?   

>
<

Model Cross Reference

This part works with the following models:

Fix Number: FIX2003651
Manufacturer Part Number: 12002213
Brand
Model Number
Description
Norge
6002A
Washer - WASHER
Norge
6002A REV A
Washer - Norge Washing Machine Model 6002A REV A (6002AREVA) Parts
Norge
6430
Washer - WASHER
Norge
6430 LOT A
Washer - Norge Washing Machine Model 6430 LOT A (6430LOTA) Parts
Norge
6430 LOT A REV A
Washer - Norge Washing Machine Model 6430 LOT A REV A (6430LOTAREVA) Parts
Norge
6430 LOT A REV B
Washer - Norge Washing Machine Model 6430 LOT A REV B (6430LOTAREVB) Parts
Norge
6432A
Washer - WASHER
Norge
6432A REV A
Washer - Norge Washing Machine Model 6432A REV A (6432AREVA) Parts
Norge
6432A REV B
Washer - Norge Washing Machine Model 6432A REV B (6432AREVB) Parts
Norge
6432A REV C
Washer - Norge Washing Machine Model 6432A REV C (6432AREVC) Parts
Norge
6432A REV D
Washer - Norge Washing Machine Model 6432A REV D (6432AREVD) Parts
Norge
6433A
Washer - WASHER
Norge
6440A
Washer - WASHER
Norge
6440A REV A
Washer - Norge Washing Machine Model 6440A REV A (6440AREVA) Parts
Norge
6440A REV B
Washer - Norge Washing Machine Model 6440A REV B (6440AREVB) Parts
Norge
6440A REV C
Washer - Norge Washing Machine Model 6440A REV C (6440AREVC) Parts
Norge
6440A REV D
Washer - Norge Washing Machine Model 6440A REV D (6440AREVD) Parts
Norge
6440A REV E
Washer - Norge Washing Machine Model 6440A REV E (6440AREVE) Parts
Norge
6440A REV F
Washer - Norge Washing Machine Model 6440A REV F (6440AREVF) Parts
Norge
6440A REV G
Washer - Norge Washing Machine Model 6440A REV G (6440AREVG) Parts
Norge
6440A REV H
Washer - Norge Washing Machine Model 6440A REV H (6440AREVH) Parts
Norge
6440A REV J
Washer - Norge Washing Machine Model 6440A REV J (6440AREVJ) Parts
Norge
6440A REV K
Washer - Norge Washing Machine Model 6440A REV K (6440AREVK) Parts
Norge
6443A
Washer - WASHER
Norge
6443A REV D
Washer - Norge Washing Machine Model 6443A REV D (6443AREVD) Parts
Norge
6443B
Washer - WASHER
Norge
6530A
Washer - WASHER
Norge
6530A REV A
Washer - Norge Washing Machine Model 6530A REV A (6530AREVA) Parts
Norge
6530A REV B
Washer - Norge Washing Machine Model 6530A REV B (6530AREVB) Parts
Norge
6530A REV C
Washer - Norge Washing Machine Model 6530A REV C (6530AREVC) Parts