OEM Kenmore Microwave Parts & Accessories

Watch the install video

$8.87

Light Bulb - 40W

★★★★★

3 Reviews

Fix Number FIX2376034

Manufacturer Part Number 8206232A

To access the exterior lightbulb, the bottom panel of the microwave will need to be removed. It is secured in place with screws, so will require a Philips screwdriver to remove it. Screw the new light bulb directly into the light socket. If this is the first time you have replaced this light bulb, the old light bulb might be held in place with silicone. This silicone will need to be cut off using either a utility knife or dental floss before removing the light bulb. Once this silicone and old bulb has been removed, the replacement bulb can be screwed in its place.

Installation Instructions

Mark from North East, PA

Bulb burnt out

Removed the screw holding the bulb cover replaced the bulb. Reinstalled the cover and screw. Remove dirty grease filter replaced with new grease filter. Read more...

Watch the install video

$19.73

Light Bulb

Fix Number FIX12751166

Manufacturer Part Number 316538904

Clear, 120 Volt, 40 Watt.

Installation Instructions

Chris from Lillington, NC

Broken bake element & light bulb

Turned of the power at the fuse box as the oven was hard wired to the electrical source and then removed the old element via the screws at the back of the oven. Disconnected the wires from the element and then reconnected those to the new element. Screwed the element base to the back wall of the oven and then replaced the light bulb. Read more...

Watch the install video

$9.37

Main Terminal Block Kit

Fix Number FIX471605

Manufacturer Part Number 5304409888

Terminal blocks (also called terminal boards or strips) provide a convenient means of connecting individual electrical wires.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Little to no heat when broiling
See more...

Watch the install video

$50.31

Temperature Sensor

Fix Number FIX820208

Manufacturer Part Number 316217002

This is a temperature sensor for a range. The sensor is what detects the temperature inside the oven and is often replaced when the oven is having heating issues. Please note that the wire connector may be different from the original; if this applies to your part, cut the quick connect and wire together with porcelain wire nuts. For this DIY repair, you will need a Number 2 Phillips or Number 2 square-head screwdriver and possibly wire strippers. Make sure to disconnect the power before installing this part. You will need to pull the range from the cabinet to gain access to this part from the back of the unit.

Fixes these symptoms

Element will not heat
Little to no heat when baking
Oven is too hot
See more...

Installation Instructions

Stephen from Ormond Beach, FL

Oven not heating to the set temperature

Suspected sensor based on above problem. The biggest problem was not knowing how hard it would be to get the built-in oven from its slot. Once it moved an inch, it was easy. The sensor inside the oven is a little hard to access because of the oven door. I would recommend a magnetic screw driver to make it easy to hold the sensor screws and allow reaching in the oven with one hand. Read more...

Watch the install video

$10.90

LENS

Fix Number FIX16218465

Manufacturer Part Number 5304524341

This is a light bulb lens, and it is made for your oven. This part protects the light bulb inside your oven by covering it. The lens is made of glass, and has a 3-inch diameter. Before making this repair, we recommend disconnecting the power.

Installation Instructions

Boyd from Birmingham, AL

Lens broken

Removed snap wire holding old lens in place, replaced bulb then centered new lens in place and put snap wire on new lens. Job done in 2 minutes. Easy as eating apple pie. Read more...

Watch the install video

$73.45

Glass Cooking Tray

★★★★★

1 Review

Fix Number FIX373741

Manufacturer Part Number 4393799

This glass cooking tray, also known as a turntable, is a genuine OEM replacement part for your microwave. The clear glass tray measures approximately 12 inches in diameter, and it is the surface that your dish sits on when heating food. If the tray has become cracked or damaged, it may result in the turntable not rotating, which means your food will not heat evenly. If this happens, the tray should be replaced. No tools are required to replace this part, simply line up the tray with the drive coupling ensuring that the three partial circles connect to the driver.

Fixes these symptoms

Tray won’t turn
See more...

Installation Instructions

John from Menifee, CA

tray was broken

replaced the tray in about 20 seconds Read more...

$68.65

DAMPER

Fix Number FIX11728088

Manufacturer Part Number W10843943

This assembly includes the damper door and frame.

Fixes these symptoms

Exhaust fan not working
See more...

Watch the install video

$39.28

RING-TURN

Fix Number FIX12584163

Manufacturer Part Number W11252182

This support ring sits underneath the glass turntable tray.

Fixes these symptoms

Noisy
Tray won’t turn
See more...

Installation Instructions

RICHARD from ROUND LAKE, IL

lost cooking tray and ring turn

open microwave door, place turn ring then place glass cooking tray on and done Read more...

$13.34

Fuse

★★★★★

2 Reviews

Fix Number FIX1960938

Manufacturer Part Number W10138793

This part protects the microwave by shutting it off if there is an electrical surge.

Fixes these symptoms

No heat
Won’t turn on
See more...

$62.87

SWITCH

Fix Number FIX8769124

Manufacturer Part Number 5304493153

The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capacitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..

Fixes these symptoms

No heat
Won’t turn on
See more...

Installation Instructions

Fred from Farmington, NM

Microwave light would turn on but the turn table would not turn and the heating system did not work.

I first read some blogs about my microwave and foud that several people had the same problem Then I removed the top vent cover(three screws through the vent easy to see and locate. Removed one screw from above the control panel and removed the control panel. This made easy access to the three mico switches that engage the door latch system. the bottom switch should some sign of heat damage (some melting) i ordered the part and reinstalled the peaces I removed and the microwave is working perfectly now. $35.00 dollar fix insted of a $250.00 microwave reolacement. I did not have to remove the microwave from its position in the cabinetry. Read more...

Kenmore Microwave Parts

Popular Kenmore Microwave Parts

Appliance Type

Related Pages

Popular Kenmore Microwave Models

Kenmore Microwave Parts

Start With Your Model Number

Popular Kenmore Microwave Parts

Appliance Type

Related Pages

Popular Kenmore Microwave Models