Microwave Oven Combo Sensors

Fix Number

FIX11758156

Manufacturer Part Number

5304504897

This is an authentic temperature sensor, which works with ranges, wall ovens, microwave oven combos, microwaves and warming drawers.

Fix Number

FIX10059162

Manufacturer Part Number

WB21X22134

If your oven is running hot, not heating evenly, not coming up to temperature, or just not heating up at all, there may be an issue with the temperature sensor. This sensor is usually found in the back of the oven or fitted onto the broil assembly, and is used to measure the temperature inside the cavity of the oven. It then sends that information back to the electronic control, which adjusts the temperature as necessary. If you need a new sensor, this is a genuine OEM replacement part. Before beginning the repair, be sure to disconnect the power supply to your oven, along with the gas if applicable.

Fix Number

FIX820208

Manufacturer Part Number

316217002

This is a temperature sensor for a range. The sensor is what detects the temperature inside the oven and is often replaced when the oven is having heating issues. Please note that the wire connector may be different from the original; if this applies to your part, cut the quick connect and wire together with porcelain wire nuts. For this DIY repair, you will need a Number 2 Phillips or Number 2 square-head screwdriver and possibly wire strippers. Make sure to disconnect the power before installing this part. You will need to pull the range from the cabinet to gain access to this part from the back of the unit.

★★★★★

★★★★★

1 Review

Fix Number

FIX1570174

Manufacturer Part Number

12001656

This is a factory-certified oven sensor kit with two harness adapters. Its purpose is to sense the temperature inside the oven. Replacing this part can fix an oven that is not reaching the proper temperature (too hot or not hot enough), not heating evenly, or an oven that will not start. To access this part, you will need access to the back of the range. Use a Phillips screwdriver to remove the screws on the access panel. Once the access panel is removed, you will notice a hole on the right side of the oven where the temperature sensor comes out of the oven. You will need to unplug the wire harness, and then open the oven door, locate it in the upper left corner, and remove the screws holding the temperature sensor in place. Pull the sensor out of the back of the oven, and replace it with your new part.

Fix Number

FIX11748765

Manufacturer Part Number

WPW10131825

This temperature sensor detects the temperature within the oven cavity.

Fix Number

FIX4240743

Manufacturer Part Number

DG32-00002B

This oven temperature sensor helps regulate heat by detecting the internal temperature during cooking. It includes a 3.9-inch probe, a 3.2-inch wire harness, and a 1.7-inch support bracket. If your oven isn’t heating properly—too hot, too cold, or not starting—the sensor may need replacing. To install, unplug the range and move it away from the wall. You’ll need a screwdriver, wrench, and drill with a Phillips bit. The sensor is usually near the heating element and may require removing the rear panel to access the wiring. Removing the oven door is optional but can make the job easier.

Fix Number

FIX236043

Manufacturer Part Number

WB21X5301

This sensor detects the temperature within the oven cavity.

Fix Number

FIX236398

Manufacturer Part Number

WB23T10015

This temperature sensor detects the temperature within the oven cavity.

★★★★★

★★★★★

1 Review

Fix Number

FIX2003225

Manufacturer Part Number

12001655

This temperature sensor detects the temperature within the oven cavity.

★★★★★

★★★★★

1 Review

Fix Number

FIX8754411

Manufacturer Part Number

WB21X10165

This temperature sensor helps regulate heat inside the oven by sending temperature readings to the control board. It ensures consistent cooking and helps maintain the set temperature. A faulty sensor may cause uneven heating or error codes. Replacing it restores proper oven performance.