MAH21PDD3W Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Seminole, FL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inner door skin worn from carpet backing rubbing in spin cycle.
Ordered part from PARTSELECT.COM, super fast shipping, next day actually, via fed ex. Part was exact replacement with no surprises. Swapped out internal parts snapped door lid cover in and was doing a wash in 15 minutes start to finish.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Downers Grove, IL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the inner door was leaking
First I remove the 2 screws that hold the door on then put it on the table on a towel not to scratch the door and unscrewed the inner door and changed it out easy stuff.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CHINA, ME
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
sharp metal edges
after cutting my hand I installed masking tape around the opening on the back of the washer. All went well after that
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from STERLING HEIGHTS, MI
- Parts Used:
- WP22003275
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Water leak on bottom outer door
Removed outer door and positioned it on counter next to new part.
Transitioned each part element from from one to the other.
Finally re-install door back in place..........
Transitioned each part element from from one to the other.
Finally re-install door back in place..........
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from SAINT CHARLES, IL
- Parts Used:
- 12001788
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Tight fit
Working from back of machine, slip old belt off drum pulley. Loosen 1/2" nut to remove drive motor from outer drum assembly. Work motor toward front of machine, while holding carefully, to slip out of old isolators. Remove worn isolators. Replace with new isolators (lip towards front of machine). Re-install motor with the nut/washer all the way up against the stop for the least amount of pressure possible on belt tension..tighten bolt. (Believe me.. when you try to install the belt, it will still seem like the belt is not the right size and way too tight.).. It is, however, the correct belt.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.
Have a zip-tie ready.
Engage the new belt on the motor shaft pulley. The belt grooves should line up with the motor shaft grooves towards the end of the shaft. Grip the drum pulley and rotate counterclockwise while guiding the belt onto the pulley. At about 12 O'Clock, zip-tie the belt to the pulley.. then rotate ccw until installed.. (about 6 O'Clock). Snip off the zip-tie and your ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from N LAS VEGAS, NV
- Parts Used:
- 12001788
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Noisy
The motor isolators went in with no problem ,but the drive belt went on very tight , your how to video shows how. Easy the belt went on , when I called your store I was told that is the only size belt for the machine model mah5500bww,
Thank you Bill
Thank you Bill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FOLSOM, CA
- Parts Used:
- 12001788
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Burn smell during spin cycle.
I followed the instruction of using a tie strap to secure belt to drive pulley and turn pulley to place belt on pulley. Worked great. Done in no time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BENNIE from FT WALTON BCH, FL
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door shroud had cracks and was leaking water
Removed and replaced old shroud with new one. Works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Morgan from GARDEN RIDGE, TX
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
leaky door
replaced inside of door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Bonham, TX
- Parts Used:
- 33002973
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
replaced two baffles
took off the dryer by remving two screws, then the front panel. Then removed the screws that held in the drum, pulled the drum out replaced the baffles then put it back together. It was easyer then I thought. It took less them 30 mins.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Ringle, WI
- Parts Used:
- WP22003275
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking front door~cause: hamper wires wriping inner plastic door liner
Removed door, changed over parts from one panel to the other, then rehung door....extremely easy! Thanks for the part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Warwick, RI
- Parts Used:
- WP22002798
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door hinge worn.
Very easy.I used a screw driver to remove and install the new hinges. Three screws on each hinge. Door closes like new again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from Stanton, IA
- Parts Used:
- 22002266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
purchased a front load washer, missing siphon cap
Ordered siphon cap according to FPS parts list. Wrong cap, but I don't care! Customer support was so helpful and willing to do everything to get me the correct cap, to include refunding my purchase price AND shipping before I even sent it back. They will be my first choice for parts in the future! My husband is a "fix it" guy, so I know that will mean a lot of purchases. I look forward to future business with this company!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sudie from Ocala, FL
- Parts Used:
- 22002266, WP22002265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing parts
Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from amston, CT
- Parts Used:
- WP22003262
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
leaking water
removed one panel and front door to access under tub.leak solved!!!! thanks
Was this instruction helpful to you?
Thank you for voting!