MAH21PDD3W Maytag Washer - Instructions

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

Syphon Cup is made one way and just slides into place...very easy

It was very easy...we ordered the part and it only took a day and a half and it was here.

Replaced it with the new inner dooor.

Ordered a new inner panel and had my son in-law put it in for me. He is a mechanic so it was a quick an easy fix.

Removed the door removed the hinges removed the screws holding the inner door in place removed all the parts under the inner door put everything back together in the opposit order from taking it out replaced the door wala! finished

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.