MAH21PDD3W Maytag Washer - Instructions

What transpired was removing the guts from the old inner door and putting them onto the new door which extended the time. Not sure about the tools because my handyman/friend did the installation while I was gone. He was a little frustrated with it. Otherwise, the door fit well. We decided that using hot water was the problem with the water leaking from the door. Using cold and warm water settings seems to make a difference.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

Followed instructions that came with replacement part, good as new!

The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

My husband, a mechanical engineer, kept forgetting to take all the brackets out to hold the screws in place and therefore had to take it apart several times to put the brackets in. Difficult time getting some of the parts out of old door to use in new one without breaking them as most were made of plastic. Washing machine works fine now.

I followed the video instructions provided, without the slightest problem. I was proud I was able to accomplish this on my own. My husband wanted to buy a whole new washer, that seemed silly, so I fixed it in about 20 minutes. And no more leaks!

Unscrewed old screws, removed old plastic pieces, and replaced

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

Removed the door from the washer and removed the screws holding the broken door panel to the outer door. Removed the clips that hold the screws in and transferred them to the new inner door panel. Removed the drain pipe and gasket (I assume that's what it's called) by unclipping the bottom from the door. There is another metal ring that had to be unscrewed. Then we screwed it to the new door panel and installed the gasket and drain pipe. Attached the new inner door panel to the outer door and screwed the door to the washer. Fairly easy repair.

removed screws holding inside panel switched clips and reset and replaced screws in outer door panel. Now works with no leaks

First thing I did was watch the video the parts company provided. It was concise and kept me from calling the appliance repair man to come right out. It looked easy enough for this 60 plus year old woman to accomplish. The steps they showed were right on. The only part I would emphasize is the rubber grommet can be installed upside down. If it is the air circulator will not fit in. Left me scratching my head for a minute or two. Once that was in the right way it was a done deal. If I had put that in right the first time the replacement would have taken half the time. What a great company!

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!

Replaced the inside door panel. Who needs a Maytag repairman! Thank you for the great instructional video.

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.