52750-5 General Electric Washer - Instructions

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

disconneted power removed two screws removed led the front clamp removed quiet hose remplace for new

Real simple, Unplug power cord from the wall outlet. Then open the top of the dryer by inserting a flat blade screwdriver under the front and pry up till the top snaps open. Lean the top to the back to keep it out of the way. Remove the 2 screws that held the front on and remove the wires for the door switch and the light. Remove the front by letting it lean out about 8 inches and lift it up out of the two bottom clips. Then just lay it any where it will be easy to work on. Clean where the new guide will go. Then just follow the instructions that came with the part. After the adhesive is fully dry just reverse the process and you are done.

removed 2 screws, and released the clips holding the top of dryer. Lift top of dryer to expose drum. Remove old drum guide. Clean old adhesive off. Apply new adhesive, and attach new drum guide.

Works like new now

popped lid pulled front scraped old seal off ,good kit ,worked great. you guys are great 2nd day delivery,on parts for fridge ice maker solenoids and dryer parts. you got me for a customer from now on. thank you. steve

I ordered parts, recieved in 2 days. came with upper glide, glue and instructions. instructions were easy to read and follow. I used the wood chisel to remove old felt, cleaned well with some solvent, reap[plied glue, wait a few minutes , apply felt - reassemble dryer - viola- done. very satisfied customer

Took off front door. Cleaned all of remaining felt left.
Put on glue and installed new part.

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.

1.) Unplug Dryer
2.) pop dryer lid by depressing 2 front clips with flat head screw dryer
3.) on back of dryer remove access cover and release belt tension
4.) remove front panel screws and then pop off front panel
5.) remove old gasket. Used XACTO knife, razor blades and acetone. Go slow and be careful.
6.) apply new high temp glue, let set up for a minute
7.) position the new felt gasket and clamp into place. I used C-Clamps and squeeze clamps.
8.) I let sit overnight.
9.) re-assemble and good to go.

NOTE: In retrospect I should have replaced both seals at the same time. The bottom seal is pretty worn but is still working out for now.

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

no problem open top remove front install new belt

tilt up lid, remove front panel, replace guide, clean out dryer and reinstall.

Unhooked old hose and replaced with new one.