52750-5 General Electric Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Pleshette from Hawthorne, CA
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Clothes were getting stuck between machine body and drying drum, also there was a squeeking and a noise that sounded as if something was clanking around, like a coin.
I watched the great easy to follow video from PartSelect. Absolutely nothing unclear. I was able to open the top and disconnect the front panel in less than 10 minutes! Removed the old felt drum glide, scraped off any stuck felt and loose glue. Then glued the new pad in place, using 3 small clamps, like clothes pins. Let it set for about 15 minutes then put it all back together! I did forget to reattach the ground wire, so I had to open the lid back up for that. About 50 minutes total. Also I took the opportunity of having the front panel off to give the inside a good vacuuming, not a ton of lint but enough to go ahead and clean it out! Thanks for the help!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Alto, MI
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Squeak and clothes getting stuck
Just want to say what a great company to order parts from, I ordered the wrong parts by mistake, broke the part trying to install the incorrect part, emailed customer service and they not only gave me credit for the wrong part I ordered but, also for the shipping...I will definitely be ordering again from this company
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from DOVER, NH
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Scraping noise from front of dryer
I had this happen a couple years ago so I knew what to do. The hardest part is getting the old glue off. I did that with some nail polish remover and a paint scraper - probably took 20 minutes just to get the glue off. From there, it's just glue on the new one and slap it back together. In hindsight, however, I would've ordered and installed the lower guide as well and done it all at once.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Flagler Beach, FL
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Squealing after dryer running 20 m inutes
Installed Upper Drum Glide. Fixed problem 90%. Sprayed silicone on pads and squeal almost all gone.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PAUL from VA BEACH, VA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burned Clothes, And Cuts In Allclothes
Popped top off with flat head, took 2 screws out with phillips head, disconnected wiring, took front off, old piece removed, cleaned with razor blade, installed new glide, all done. I am sorry I waited so long to try this. So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Ukiah, CA
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
clothes getting stuck in drum and leaving brown marks on them
I want to suggest that you also purchase the lower drum seal or guide as well. When I took it apart I realized I needed it also.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Live Oak, FL
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
drum was lose and was marking clothes
watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pittsboro, NC
- Parts Used:
- 5303937139
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Clothes were getting trapped at edge of drum and were being burned.
Pulled dryer forward for access. Raised top by pressing clips on front. Removed front panel 2 screws. Removed old felt flange with plastic guides. Cleaned surface of old glue. Dried. apply cement per instructions applied new felt. New fit was snug and required some manipulation. When in place it helped to hold felt until cured. works great. Would not have known what problem was without the videos @ Part Select. Thanx for info and part. David
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from howell, AL
- Parts Used:
- 5303937139
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
thin cloth materials getting stuck between drum edge, leaving rust marks.
lifted up the top after releasing 2 catches with the putty knife, removing front panel, held in place with 2 screws. Scrape off top felt strip with the worn teflon tabs. Wire brush off old glue. Apply glue provided.(thin coating). install new felt strip. let the glue dry for a few minutes, reinstall, and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William H. from Warsaw, OH
- Parts Used:
- 134101800
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The washer lid lock was burned
UNPLUG APPLIANCE....very simple installation. Raise THE top and the switch is in the corner. Unplug the wiring harness and remove the 2 screws that hold the lid lock on. Reverse the procedure and replace the lid lock.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Santa Maria, CA
- Parts Used:
- 131859104
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob broken
Pushed the new one in place. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Orange beach, AL
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old lint filter was bent and screen torn.
Ordered a new lint filter around 2 pm and received it UPS the following day. Popped it in and we're good to go. Could not have been faster or easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Silver Spring, MD
- Parts Used:
- WE16X29397
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was busted
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from hudson, NY
- Parts Used:
- WE03X29897
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
belt broken
watched video and followed instructions. Made my wife very happy not having to buy a new dryer. Thank You, Joe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john l from cumberland, RI
- Parts Used:
- WE03X29897
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Belt Was Broken
I watched the installtion video and actually did it faster than the video and yes you do have to be careful of sharp edges I did cut one finger. Other than that no problem I was all back together and using the dryer in less than 15 minutes
Was this instruction helpful to you?
Thank you for voting!