Models > 52750-5 > Instructions

52750-5 General Electric Washer - Instructions

Jump to:

All Instructions for the 52750-5

Customer:: Cecil from Jacksonville, FL
Parts Used:: 131461200
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Washer leaks when spin drying

Put the front up on a 4 X4 block. Removed the two screws at the bottom of the front panel. Slid the front panel down and off. With pliers squeezed the spring clamp and removed the hose, slid the hose out of the machine. Slid in the new hose into the hole in the back, put the spring clamp on the hose, slid the pump end of the hose onto the pump and using pliers put the spring clamp back on. Put the front panel back on and the screws, removed the block. Tested the washer.

Was this instruction helpful to you?

Customer:: Gregory from Piscataway, NJ
Parts Used:: 131862900
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins

Replace belt

Hard to reach around the motor and gear box to attach the belt and pulley not much room. Harder to put the front pannel back on than take off

Was this instruction helpful to you?

Customer:: Carolyn from Orange beach, AL
Parts Used:: WE16X29397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Old lint filter was bent and screen torn.

Ordered a new lint filter around 2 pm and received it UPS the following day. Popped it in and we're good to go. Could not have been faster or easier!

Was this instruction helpful to you?

Customer:: Joseph from Silver Spring, MD
Parts Used:: WE16X29397
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

filter was busted

Replaced

Was this instruction helpful to you?

Customer:: Pauline from Kelseyville, CA
Parts Used:: 134101800
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Wouldn't rinse, spin, or pump out the water

Ordered the part online from PartSelect and it arrived Friday morning just 3 days later to my front door. Removed 2 screws, disconnected 2 wires, screwed the new part into place, plugged in the new wires and it still didn't work. Looks like my washer is just too old. So . . . I called PartSelect, explained everything. Three days later a full refund was in my bank account. Shop PartSelect with confidence. I will be back!

Was this instruction helpful to you?

Customer:: Vincent from NORTHVALE, NJ
Parts Used:: WE03X29897
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

Drive belt for dryer frayed and making noise

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Was this instruction helpful to you?

Customer:: TIM from NORTH AURORA, IL
Parts Used:: WE03X29897
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Screw drivers

Bearings,belt squeaking

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Was this instruction helpful to you?

Customer:: David from Santa Maria, CA
Parts Used:: 131859104
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Knob broken

Pushed the new one in place. Done!

Was this instruction helpful to you?

Customer:: Gerald from Battle Creek, MI
Parts Used:: 5303937139
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Screw drivers

Removing old felt and glue

After removing the old drum glide there was tufts of felt and glue left behind. The DIY video (which inspired me to try this repair myself) says to use a scraper and wire brush to clean the drum edge. I decided to try a drill with a wire wheel. Worked great. The surface was shining clean in minutes.

Was this instruction helpful to you?

Customer:: James from Mitchell, SD
Parts Used:: WE03X29897
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

broken belt

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Was this instruction helpful to you?

Customer:: Tom from Aquone, NC
Parts Used:: WE03X29897
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Dryer Belt Squealing

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Was this instruction helpful to you?

Customer:: Michael from Lucas, IA
Parts Used:: 5303937139
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Screw drivers, Socket set

clothes getting caught around drum leaving marks on them

took front off machine removing screws. Removed old felt and cleaned old glue off making sure area was clean. applied new glue and then new felt drum glide. put fish sringer around complete drum pulling tight clamping with vise grips till dry. then put front back on machine.

Was this instruction helpful to you?

Customer:: robertt from rio grande, NJ
Parts Used:: 134101800
Difficulty Level:: Really Easy
Total Repair Time:: 1- 2 hours
Tools:: Screw drivers

would not drain

followed on line instructons very easy

Was this instruction helpful to you?

All Instructions for the 52750-5