52750-5 General Electric Washer - Instructions

After not being able to get the proper 10 foot hose, and having to splice two drain hoses together....turned out it was not the drain hose after all, but the pump. Some sort of "baffle" in the drain hose, where the rubber connector at the pump end and the corrugated hose joins, was blocking the water I thought. It may have been since a spliced the new hose in at that end. However, I think it was the pump.

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

Moved dryer out where I could get to all sides, then pulled top off, then unscrewed the front panel. The drum lifted out of it's ball bearing assembly in the back with a little force. Then it slid out fairly easy.

I replaced the rear bearing assembly, the bottom drum glide strip, the top drum glide and the vent seal all at the same time. The glue for the glide strips took about an hour to set up and I used clothes pins every 4-6 inches as suggested by someone else here on this site. Then I vaccuumed out the entire dryer body, vent pipes and every nook and cranny.

I put everything back as it had come out and then put the dryer back in it's place. Plugged it back in and it's as quiet as when it was new. Total time of project was about 1:45.

Found the promblem as described at this site while looking for diagrams for the dyer. Repair went as described. Once I removed the old upper drum glide I used acetone to remove old glue. Cleaned up fast and easy. Once installed I let cure for about an hour and then reassembled. Let it cure for about an hour more and then I used the dyer. I could feel that the gap around the front of the drum was again narrow so that my finger tip would not slide into a grove. So far so good.

Followed the instructions in the video. It was very helpful.

Drain hose should come with the two clips (45B)that hold the drain hose to the back of the machine. I had to cut the old hose off. Then very carefully remove the clips from the inside of the machine with a pair of pliers.

Popped the tub cover off....replaced with new one.
Thank you so much for a speedy delivery.

i took the hose of and stuck the water hose in it and saw a lin hole leak. i order a new hose and recived it very fast (1 day) took 15 min to put it on the pump and to put the machine back togther

I removed the top lid, then removed the front panel, to expose top and bottom drum glides attached to panel, then using a carpenter shisel, and cutting knive scraped away the old worn out glides, wiped clean with acetone the area were the new glides were being cemented. all of this thanks to couple of customers that had the same issues on their dryer, and documented step by step their own way to have this done, I just followed thru their experiences.

1.) Unplug Dryer
2.) pop dryer lid by depressing 2 front clips with flat head screw dryer
3.) on back of dryer remove access cover and release belt tension
4.) remove front panel screws and then pop off front panel
5.) remove old gasket. Used XACTO knife, razor blades and acetone. Go slow and be careful.
6.) apply new high temp glue, let set up for a minute
7.) position the new felt gasket and clamp into place. I used C-Clamps and squeeze clamps.
8.) I let sit overnight.
9.) re-assemble and good to go.

NOTE: In retrospect I should have replaced both seals at the same time. The bottom seal is pretty worn but is still working out for now.

Pulled the dryer front off to expose the problem. Thought it had a bearing of some type. Went to the PartSelect web site and watched the repair video. The Tech explained everything needed to make the repair. Ordered the parts kit and it arrived in three days by FedEx. Followed the directions. Simple. The video was excellent and made the repair a snap. Thanks.

* Clean off top of stackable dryer and remove top lid (pops off w/ screwdriver)
* Disconnect power supply and control wiring (right side under top lid)
* Remove left and right single screws securing front face of dryer
* Pop off dryer face w/ screwdriver
* Remove existing top glide from dryer face (peels off, use screwdriver or chisel/scraper to remove residue from felt and glue)
* Test fit new top glide
* Apply adhesive (included) to dryer face rim
* Clamp with 4 or so spring clamps and allow adhesive to set up (I waited about 30 minutes).
* Clean and inspect inside of dryer while the front face is off
* Clean dryer vent assembly (attached to dryer face)
* Reassemble and test easy rotation of the drum prior to use

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

Watched two videos...totally easy. Might have been able to stumble my way through it in 3 times the time. Watched the video and entire fix took about 45 minutes...awesome.

repaired as described in your instructional video.The video repair part of your website is just great.Seeing it done vs tring to understand someone else describe it makes it that much easier. I will use you for all future repairs.