NAH6800AWW Amana Washer - Instructions

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

The repair was very easy after watching the video that was with the part. I will continue to use this site for other repairs that need to be done.

I went on your web site and printed the instructions given by the first entry after the product description. I had called my friend who is also a handy man and he did the repair very quickly [I helped very little]. The directions were very complete and very simple to follow. MAH5522BW

The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.