NAH6800AWW Amana Washer - Instructions

Removed front panels, lifted top to open position, removed back cover, removed drive belt, drum pulley, removed rear bearing snap ring, removed seal clips, removed 3 baffels then the 3 mount bolts. Pulled out spinner support and the inner drum. Removed the rear bearing #6206LL with brass drift rod and heavy hammer (came out with little effort. The front bearing #6207LL I soaked with penatrating oil overnight (this bearing was making all the noise as after 11 years water finally got to it) The next morning I had little trouble removing it with the brass rod and hammer, taking my time to work my way around driving it out. After cleaning everything up, assembly was the reverse, carefully driving in the new bearings. The new lip seal was the most difficult getting started without going in crooked. Time spent was a good 8 hours (it would have been more if the outer drum was removed) and the cost of everything was $167.09. Thanks to Part Select, the spinner support assy came the very next day. The two bearings came from Bearing Supply & Depot Inc. The washer operates like new!! Very Quiet!!

Turned washer off and unplugged.Removed 2 screws and metal plate on back of washer. Removed the old water inlet valve by first removing 4 wire metal/plastic connections (2 on top and 2 on bottom of valve. Next removed the hose, just a bit difficult to grip as hose was short and mostly inside washer. When replacing with new part, connected hose to water inlet valve first and then the 4 wire connections. Replaced the metal plate on back of washer with 2 screws.

I follwoed the detailed instructions provided via the Part Select web page and instructional video. This information was very helpful. I printed the step by step paper instructions and had them available at the washer. They were very easy to understand. By doing this work myself I saved a $100.00 repair service call and installation cost and another $30.00 on parts. This resulted $130.00 ++ savings and 30 minutes of my time. Thanks for the great help and guidance!!

I just replaced the pump.

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

We noticed there was something missing to hold the fabric softener. We found on-line the parts we needed. Ordered at about 4:00 PM and it came at 10:am the next day!!! Done!

The service representative knew exactly what was needed from the description of the problem that was given to her. The hinges were received within a few days. The door was removed and the hinges were replaced and it does not sag anymore. Thank you for your great service.

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

I am happy when PartSelect included the instruction video, so I completed my repair that easy. Thanks the PartSelect. Davis Dao

We noticed water below our Maytag Neptune front loading washing machine. I identified the leakage from the water inlet valve. The schematic that you had on your site allowed me to select the correct part. The part arrived very quickly.. 2 business days. 5 minutes to get the old one off and 10 to place the new one on and we were good to go. I figured I saved at least a $350 service call! Thank you!

I found the part at PartSelect. I unplugged the power, turned off the water and removed the hoses from the back of the machine. I removed the front loader door by removing the philips head screws on the door hinge. I removed the philips head screws on the frame opposite the hinges. I removed the front. I then took the 4 philips head screws out of the detergent/softener dispenser on the top, and removed those parts. After this, I lifted the lid. At the back of the machine was the blue hot/cold water valve. I loosened the hose clamp with a nut driver on the thermister end, and removed the hose. I then removed the mounting bolt with a nut driver. I installed the new part reversing the order given above.

When I looked up the part number, there was an installation video on the same page. I ordered the part then and there, and once it arrived, I put the iPad right on top of the machine and paused the video whenever I was doing the steps. It was TOO EASY!

Purchased the pump from parts select. Maytag wanted 250.00 for the pump!. Followed previous instructions from this site and had no problems. Washer still does not fully drain. Believe the problem is the filter. Maytag either couldnot/would not tell me me where to replace the filter. There is a spare filter taped to the inside of the washer. Maybe it fits inside the tub, above the outlet tube leading to the pump. Will check and see at a later date, unless I see a response on the website. Thanks.

It was very easy...we ordered the part and it only took a day and a half and it was here.