GMMP280ED4WS General Electric Dryer - Instructions

Watched the video on a different style of dryer so taking apart a bit of a challenge. The old Front Drum Bearing was completely gone on left side and a challenge to pry it off the front dryer panel. replaced felt seal and front drum bearing. noticed that there was 4 places for new bearing slides. the ones i ordered were white and green but did not know why or which one went where as no explanation with packaging. also only ordered one of each and so now had to stop and try and find two more. ! hour later i had brought back a tupperware lid that was thick enough and stated could go to 194 degrees F. i cut out one replacement for green bearing and reused the old white one since it was in good shape from right side of drum bearing. i went back to this website and noticed in the comments section for drum bearing that someone stated the green bearing slides go in at positions 11 and 1 and the white at 10 and 2. they are different materials and having more weight of drum on green now made sense. put machine back together and told neice to keep eyes and ears on dryer thru cycle. she did not even know it was running just in next room.

Exactly how your perfect video instructions showed me. Thank you for a job well done!

The repair made it necessary to remove the door of the dishwasher. Removing the door seemed to be a daunting task, but after watching a YouTube video I made myself aware of the necessary steps to complete the task.

- After turning off the power to the dishwasher, I removed the kickplate panel, this gave access the wiring going to the defective board, which I unplugged.
- Removed the screws securing the dishwasher to the counter, these are located at the top of the machine and are accessible by opening the dishwasher door.
- Pull the dishwasher forward a few inches.
- On each side of the door is a spring loaded device that holds the door from falling open when not latched. They can be identified as white plastic items with a cable connected to them. Once removed take care to not allow the door to fall open, instead, when opened slightly raise the door off the unit.
- Lay the door on the floor.
- There are three sheetmetal screws on each side of the door, using your nut driver remove these screws. They secure outside of the door to the inner door.
- Stand the door up on the floor and raise the outer door panel, there are several plastic clips on each side the slide into slots on the inner door panel. I found it a little difficult to separate the panels, but with gentle persuasion they came apart.
- Lay the inner panel on the floor with the exposed electrical components facing up.
- At the top of the inner panel is a black plastic cover protecting the electronic components, this where the control panel lives.
- Remove the sheetmetal screws that secures this plastic cover.
- There are two wiring harnesses, remove them.
- The defective component can be lifted out.
- Install the new control panel.
- Reassemble.

Once I figured out how to remove the control panel. The rest was very easy. Upon pulling off the knob in the center of the control panel, there was a screw behind it. Once removed I used the palm of my hand and gave it a couple of upward hits in the center while the door was open. It slid up and I removed the electrical connections. Then carefully removed the top by pushing from the rear of the machine slightly and lifted off. Then removing the screws that hold the front on . After that it went pretty easily, reassembly went in reverse and. That was that!

Parts diagram shows Striker can be popped out with screwdriver. Not true. It has a screw bolting it internally. Impossible to get to unless you disassemble the entire door. We took a power drill and small drill bit and bore it out like a cavity in a tooth. Needle nose pliers to extract the screw. Pretend your a dentist. Fixed it in 5 minutes. Replacement fit tight. A+

Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.

My daughter, who has the dryer in Florida, made the repair herself. She removed the broken handle that had been temporarily taped in place. Cleaned off tape residue with Goo-Gone. Then took the new handle and snapped it into place. Worked just like it was supposed to.

I pulled the old handle off and pushed the new one on.
No problem at all.

remove the old one and put the new one...!!! Easy

Replace both micro switches.

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

just replaced the unit handle and how my wife can open the dryer without a screwdriver

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)

Unscrewed the old bulb using the lefty loosey method. Installed the new bulb by turning it clockwise or righty tighty.

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.