GMMP280ED4WS General Electric Dryer - Instructions

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.

First I unplugged the dryer. Then I removed the back panel and removed the front knob from the timer. Following the instructions provided with the part, I removed the wires one at a time from the old timer and connected them to the new one. After reassembling the dryer ...........it worked perfectly !!!

Snapped on new handel. Took all of 5 seconds. The hardest part was finding the part, which your website took care of....Thanks!

I noticed that some clothes were coming out of the dryer looking like they had been chewed on. The next day something actually caught on something inside the dryer near the door. There was a broken piece of plastic. I wrote the dryer model number down and came to this website. I easily determined it was the drum bearing from the pictures provided by this website. The part came 5 days later. I think it would have been sooner, but I ordered on a Friday before a 3 day weekend (Memorial Weekend). I did not order the slides recommended to be ordered with it because my dryer was not making noise. When I replaced the drum bearing, one slide was worn completely through and the others were fine. The one worn through was right near where the plastic on the drum bearing was broken. I ordered a green slide to replace the one that was worn through.

Replacing drum bearing required the removal of 4 screws total. 2 inside dryer doorway, these two were facing towards the ceiling. After removing those two the dryer top popped off easily and did not require the removal of the control panel at the back of the dryer. The other two screws were inside and were small screws which held the front dryer panel onto the sides. After these were removed I pulled the front panel away enough to get to the drum bearing. Easy Peasy!

Removed door and two screws to replace the door handle. Reassemnled in reverse order. It was a snap.

Installed new part

Very satisfied. I simply took the plastic door handle out of the package and snapped it into the door. It popped right in and fit perfectly!

This is the 2nd time in 3 years I had to do this repair. There needs to be a better design. I suggest that when you hear squeeking that you replace the teflon pcs fast so you don't have to replace the drum bearing.
Now for the repair. Take dryer door off (4 screws) it makes the repair easier. There is 2 long screws that hold the top to the front of the dryer. Once removed you can pull out the top of the front of dryer and it unhooks from the bottom. I suggest using the vacuum and clean thoroughly while you have it apart. Unplug the wire for the light (3 wires) so you can completely remove the front of the dryer. The drum bearing snaps out (after you remove the light bulb). Insert 4 new teflon pcs into new drum bearing before re-attaching to dryer. Plug the wires back in and put the light bulb back in. Hook the bottom to the dryer and make sure bearing goes areound drum when putting back on. Put 2 long screws back in to attach the top to the front. Re-attach door and your job is done. You should not have to disconnect dryer from gas but you should unplug dryer. This is a very easy repair. I don't know why they call this part a drum bearing when there is no bearings involved at all.

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

First I removed the two screws on the underneath side in the door at the top and removed the old drum bearing and installed new one with the 2 new plastic slide bearing. It was easy and I will tell all of my friends and family about the website. Service was fast and simple to order the right part. Thank you.......Linda

The top and front of the dryer had to come off, and taking off the top (and later putting it back on) was the hardest part. The old seal was stretched approximately two feet longer than the replacement part, and its thinness caused the drum to squeak as it scraped by the door panel. We simply pressed the new seal into place after pulling out the old one. Piece of cake. Putting the front of the dryer back on was simple as well. Fitting the top back into its slots properly was the biggest pain of the whole ordeal. The part came in about 2 days. Thanks!

This dryer uses pieces of slippery plastic on a plastic support attached to the dryer front as a drum bearing. Over time the slippery plastic wears out and the underlying support will wear through like mine did.
To replace this, first unplug the dryer and then remove the two screws inside the top edge of the door opening to free the top of the dryer cabinet. You may want to remove the door first for easier handling. Next lift up the cabinet top and pull it free to expose the drum and bearings. The front of the dryer is held on with two screws at the top front corners, remove these and tilt the front forward to expose the drum bearings. remove any remaining plastic sliders and pull the old bearing support free, stating at the top and watching out for the light bulb if present. Then install the new bearing support and replace the sliders. Now tilt the front panel back into place, guiding the bearings into the drum and lining up the tabs and slots. Replace the screws, this requires some fiddling to get the alignment right, then work the top panel back into place, reinstall the screws in the door opening and replace the door if it was removed.

just snap in replacement

Just popped the new door handle on.