Models > GMMP280ED4WS > Instructions

GMMP280ED4WS General Electric Dryer - Instructions

Jump to:

All Instructions for the GMMP280ED4WS
61 - 75 of 267
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Anthony from TALKING ROCK, GA
Parts Used:
WD08X23477
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Started leaking on wash cycle from bottom left corner of door
Removed old seal and replaced with seal #WDO8X23477. Seal went in well but it was supposed to have about 2” left over on each on the bottom to curl towards the tub. According to instructions with stainless tub this did not so it still leaks some. Old seal has 2” extra at bottom. So did not work for my application.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from CASEVILLE, MI
Parts Used:
WD21X10490
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ron from AIKEN, SC
Parts Used:
WE04X20089
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Replaced timer and knob
Removed 3 screws that hold on front plate. Snapped out timer and replaced with new one. Attached one wire at a time from old timer to new timer. Reattached front panel and put on new knob. You can also watch on utube.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dENVER from MILTON, WV
Parts Used:
WE04X20089
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The dryer only provided heat on the timed settings - on other settings, the drum rotated but there was no heat
The repair is straightforward. Three phillips head screws along the top on the backside hold the control panel in place. Once the panel is loosened, the timer can be lifted from its mounting. Holding the new timer in one hand, carefully remove wires one at a time from the old timer and placing them on matching points on the new timer. Once all the wires have been moved from the old timer to the new timer, place the new timer in its mounting and reinstall the control knob. Finally reattach the panel with the three phillip head screws. Job complete.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Bud from RCH CUCAMONGA, CA
Parts Used:
WE01X20419
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Broken door handle
Snapped right into place , less than a minute, if that
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Neil from NEW YORK, NY
Parts Used:
WD08X23477
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Margaret from NORFOLK, VA
Parts Used:
WE04X20089
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Dryer Timer Knob not advancing properly.
I thought the dryer timer had gone bad, but was probably just the knob. Exact parts on this site. Pulled dryer out at angle to access back. Removed the three top screws and the front panel easily pulled off. Removed knob to release the part and realized that the knob was probably the problem! Broken plastic.... I still replaced the dryer timer since the dryer is 2014. Took photo to ensure all wires replaced in same spots. Both parts had a letter with the wire color as well. I watched a youtube video and knew I had to rotate the timer counterclockwise to remove it from the panel - two slots hold it onto the panel. I pulled the wires one at a time, some needed pliers to remove. Installed wires on new part, installed timer on panel clockwise, re-attached front panel. When I re-installed the knob, it failed. I ordered the knob from here and used the signal knob temporarily until it arrived. Works great with new knob.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from TOLLAND, CT
Parts Used:
WD08X23477
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Dishwasher tub was leaking
Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
janet from martinsville, IN
Parts Used:
WE1X1192
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
dryer did not latch
easy to fix took less than 10 minutes
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from West Bloomfield, MI
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Plastic handle in dryer broke off.
All I neede to do was buy the new part and snap it into place on the door. The hardest part was making the door usable while waiting for a new handle. The solution was good old duct tape. I just taped the old broken handle in place until the new one showed up.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rick from Nora Springs, IA
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bottom part of handle was loose
Opened up the package and took off existing door handle. The new one snapped right into place. This took all of 10 seconds!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
richard from pleasant grove, AL
Parts Used:
WE01X20419
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Plastic Door Handle Cracked
Old handle popped out by pulling back and out. Inserted new handle by pushing in and forward. Easy!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
MARIE from SAUGUS, MA
Parts Used:
WE05X20431, WE5M48
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Had to use y tube
After speaking with your representative and him explaining how to me how simple it would be to switch out this light socket myself. I went on y tube went through the instructions and had to go buy a new dryer. And before you jump to any conclusions I can and do repair and and all of things around my house. I will NEVER purchase anything from you company again ander the pretense that it is so simple. This should have been told to me that an election should have done the job!!!!!! Now not only am I out the money I paid your company but I’m out the money I shelled out for a whole new dryer. I am a very angry customer and I would never recommend you to anyone!!! EVER!!!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joseph a from VALLEY STREAM, NY
Parts Used:
WE03X29897
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
belt broke
had a great video to follow, made it easy to install.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Alvino from newtown, CT
Parts Used:
WE03X29897
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Dryer belt was broken
I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GMMP280ED4WS
61 - 75 of 267