Troy-Bilt Parts

★★★★★

★★★★★

4 Reviews

Fix Number

FIX9988561

Manufacturer Part Number

647-04271-0637

Replace a bent or damaged grass catcher with this black metal frame, designed for select 21-inch walk-behind mowers. One rear mounted frame is included, the fabric grass bag it attaches to is not included. Verify compatibility with your model before ordering to ensure it is a fit for your mower.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX19272260

Manufacturer Part Number

734-04018C

This is a genuine OEM replacement part, it is sold individually. This is the front wheel on the models shown below. There are two of them on each mower. The wheel has a ring gear on the inside which is driven by the Right hand and Left hand smaller gear that attaches to the front axle on the transmission assembly.

★★★★★

★★★★★

1 Review

Fix Number

FIX11813377

Manufacturer Part Number

946-05124A

This is an authentic OEM part. The MTD deck engage cable is composed of metal and plastic parts, and has been designed for use in several tractor machines. This part is fastened onto the frame assembly. The deck engage cable works to move belt idler pulley and engage the cutting blades. Please refer to manual for specific repair instructions. A wrench and a screwdriver is helpful in making the replacement. This part is sold individually.

★★★★★

★★★★★

1 Review

Fix Number

FIX9169783

Manufacturer Part Number

942-0741A

This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces along the edges of the blade. If installed correctly this part will keep the grass clipping under the deck longer, and re-cut them. The blade is 21 inches long, and sold individually.

Fix Number

FIX11813755

Manufacturer Part Number

954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Fix Number

FIX19305064

Manufacturer Part Number

946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

Fix Number

FIX9096195

Manufacturer Part Number

714-04040

This bow tie cotter pin fits snow blowers, as well as other gardening tools. The pin helps secure the auger to the shaft on a snow blower. Due to constant wear, this is a commonly replaced part. Tip: Extra pins are recommended. *Please note: this part is sold individually. For installation instructions, refer to the diagram provided by the manufacturer.

Fix Number

FIX12685355

Manufacturer Part Number

946-04230B

This is a genuine replacement clutch cable sourced from the original equipment manufacturer, designed for use with MTD and Yard Man snowblowers. It serves as an identical replacement for a missing or damaged cable originally installed on new units and plays a vital role in engaging the auger for proper snowblower operation. Made with high-quality rubber insulation, this durable component is sold individually. Please note that the housing, trigger, and hardware are not included and must be purchased separately. For proper installation, refer to your model’s diagram, and be prepared to use tools such as pliers and a wrench set.

Fix Number

FIX9110822

Manufacturer Part Number

738-04124A

Designed for use in MTD, Yard Machine, Troy-Bilt, Yard-Man, and Craftsman machines, this OEM approved Shear Pin fits a variety of models. For full compatibility, please see the "Model Cross Reference List" below. This is a shear pin for your lawn and garden equipment, most commonly your snow blower. It is designed to snap if your auger gets jammed or clogged, to protect your snow blower from further damage. Because this part is meant to snap at a certain point of pressure, it is a commonly replaced part in snow blowers. Consequently, we recommend keeping a spare on hand. This Shear Pin is approximately 1.75" long, and is sold individually.

Fix Number

FIX11813754

Manufacturer Part Number

954-04050A

This replacement V-Belt is a genuine OEM sourced part, not an aftermarket imitation. It is commonly utilized on snow blowers. This is the drive belt that would spin the augers. Inspect belts periodically and replace them when worn or stretched to maintain peak performance. This part is made from rubber material and it is sold individually. To replace this belt you will need a wrench set.