OEM Troy-Bilt Lawn Mower Parts & Accessories

Lawn Mower Variable-Speed Belt

$59.43

Fix Number: FIX9186148
Manufacturer Part Number: 954-0467A

This is a Genuine replacement Belt designed for use with Riding Lawn Tractors/Mowers. This part is made out of Rubber and it is Sold Individually. This is the the Belt that drives your unit. Make sure to clean pulleys before installing the new belt to ensure top performance and longevity with your new belt. Inspect belt periodically and replace it when worn or stretched to maintain peak performance. You would need a Wrench set and Pliers to replace this belt. • For your safety make sure to disconnect the spark plug wire. • Loosen the transaxle pulley • Relieve tension on the upper drive belt • Remove the upper drive belt and lawn mower belt guide • Secure the new belt • Reassemble and tighten the pulleys

V-Belt

$59.43

Fix Number: FIX11813755
Manufacturer Part Number: 954-04060C

This is a Genuine Manufacturer Approved replacement V-Belt used on Riding Lawn Mowers. This part is made out of Rubber and it is sold individually. This is the Belt that drives the Blades. Clean the pulleys off before installing the new belt to ensure top performance and longevity with your new belt. Inspect belts periodically and replace them when worn to maintain peak performance.

Watch the install video

Grass Catcher Frame Assembly

$50.22

★★★★★

4 Reviews

Fix Number: FIX9988561
Manufacturer Part Number: 647-04271-0637

Replace a bent or damaged grass catcher with this black metal frame, designed for select 21-inch walk-behind mowers. One rear mounted frame is included, the fabric grass bag it attaches to is not included. Verify compatibility with your model before ordering to ensure it is a fit for your mower.

Axle Asm-rear 11

$46.76

Fix Number: FIX16386134
Manufacturer Part Number: 611-04144B

This authentic component is sourced directly from the original equipment manufacturer. It is specially designed for use with push lawn mowers. It is an identical replacement for a damaged or a missing rear axle assembly that was installed on a new unit. This is the part that the wheels are attached to. Refer to the diagrams of your model for the exact location and the correct installation of this component. Note, it is made of durable metal and is sold individually. You will need a wrench set and a screwdriver to remove the wheels, disconnect the old axle assembly and attach the new part.

Installation Instructions

Ricky from JOLIET, IL

The adjustment lever attached to the rear axel assembly, which is used to raise/lower the rear wheels was broken off.

Removed dust covers, nuts and rear wheels from rear axel assembly. Tipped mower onto side per manufactures instructions. Removed rear axel assembly from slots (standard screwdriver used here to pry). Installed new assembly by reversing the above steps. Read more...

Watch the install video

Mulching Blade

$35.34

★★★★★

1 Review

Fix Number: FIX9169783
Manufacturer Part Number: 942-0741A

This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces along the edges of the blade. If installed correctly this part will keep the grass clipping under the deck longer, and re-cut them. The blade is 21 inches long, and sold individually.

Fixes these symptoms

Mower blade does not cut
See more...

Nut-flglk 5/16-18

$6.51

Fix Number: FIX9092936
Manufacturer Part Number: 712-04063

This nut is fit for lawn and garden equipment and is used to resist loosening when properly threaded onto a bolt. The nut is sold individually. The diameter of the nut is 5/16 inches and the thread size is 18. Refer to the manual provided by the manufacturer for repair instructions.

Watch the install video

CABLE-CONTROL 37.5

$18.74

Fix Number: FIX19305064
Manufacturer Part Number: 946-04661A

This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When the control handle is released, the control cable stops the blade. If the cable breaks, the brake will not release even after pressing the lever. To remove the old cable, cut off any cable ties, remove the cable end from the control bail, and remove the control cable from the engine (you may need pliers). Remove the cables from the openings on the handle, which can be twisted off by rotating the cable at a 90-degree angle.

WHEEL-GEAR 8-INCH INTE

$25.36

★★★★★

2 Reviews

Fix Number: FIX19272260
Manufacturer Part Number: 734-04018C

This is a genuine OEM replacement part, it is sold individually. This is the front wheel on the models shown below. There are two of them on each mower. The wheel has a ring gear on the inside which is driven by the Right hand and Left hand smaller gear that attaches to the front axle on the transmission assembly.

2-in-1 Blade

$37.49

Fix Number: FIX16463287
Manufacturer Part Number: 942-04308A

This mower blade is designed for use on 42-inch cutting decks and supports efficient grass cutting for bagging or side-discharge applications. Its durable construction and balanced design help deliver a clean, even cut while maintaining smooth operation during mowing. Replacing a worn or damaged blade restores cutting performance, improves lawn appearance, and helps ensure reliable, consistent operation of the mower throughout the season.

Upper Handle

$42.61

Fix Number: FIX16424685
Manufacturer Part Number: 749-05084B-0637

This replacement handle is a genuine OEM sourced part. It is specially manufactured for walk behind and push lawn mowers. Upper handle allows user to control the lawn mower. It is attached to the lower handle assembly that is sold separately. This part is made out of metal and is sold individually. Please note, the control bar, knobs and cables are all sold separately. You will need a wrench to replace this upper handle. • Disconnect the bail bar • Detach the control cable • Remove the bolts and the nuts that secure upper handle • Secure the new handle using the same hardware • Reattach the bar and the control cable

Installation Instructions

Ronald from SPEARFISH, SD

Replace sheave plate and side skid shoes on snowblower.

Remove eight bolts and two skid shoes and bottom sheave plate. Replace in reverse order.
Most important, get the correct OEM parts from FIX.com. Refer to product parts list in model instruction manual.
Do that first and you too can see how easy this repair is and save big bucks charged by retail repair shop! Read more...

Troy-Bilt Lawn Mower Parts

Popular Troy-Bilt Lawn Mower Parts

Installation Instructions

Installation Instructions

Troy-Bilt Lawn Mower Appliance Types

Related Troy-Bilt Lawn Mower Parts

Popular Troy-Bilt Lawn Mower Models

Troy-Bilt Lawn Mower Parts

Start With Your Model Number

Popular Troy-Bilt Lawn Mower Parts

Installation Instructions

Installation Instructions

Troy-Bilt Lawn Mower Appliance Types

Related Troy-Bilt Lawn Mower Parts

Popular Troy-Bilt Lawn Mower Models