Models > TB230

TB230 (12AVB26M011 2010) Troy-Bilt Lawn Mower

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for TB230

Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
This is a genuine OEM replacement part, it is sold individually. This is the front wheel on the models shown below. There are two of them on each mower. The wheel has a ring gear on the inside whic...
No Longer Available
This is a mulching blade for your lawn mower. It is located underneath the lawn mower deck, and cuts the grass by rotating. This blade has a curved style shell, and includes extra cutting surfaces alo...
In Stock
This is an authentic 51-inch control cable for walk-behind lawn mowers. This part is made up of a metal wire cable with a Z-type bent end on either side, and a 37.5-inch rubberized outer cover. When t...
No Longer Available
No Longer Available
This is a bell blade support, also known as a bell spacer, for your lawn mower. It is fitted between the bottom of the blade, and the blade bolt. This part provides support for the blade. It is made o...
In Stock
This is a TT screw, but it is also called a fastener, and it is used on multiple outdoor tools. This part is a Tri-Round or Tri-Lobular thread forming screw, it is 0.25 inches in diameter, 0.5 inches ...
In Stock
This is a flange lock nut, and it is used with various outdoor tools and equipment. The flange lock nut is all one piece. It has a bottom circular flange and a smaller top hex section. This is a torqu...
In Stock
No Longer Available
In Stock
In Stock
No Longer Available
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.
Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
April 29, 2022
How to set choke
For model number TB230
Fix.com logo
Hello Robert, thank you for your question. Based on our research, the spec sheet shows "190cc Briggs & Stratton no prime, no choke engine features two-pull Starting. " We hope this helps.

Was this helpful?
Thank you for voting!

Common Problems and Symptoms for TB230

Viewing 1 of 1
Mower blade does not cut
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
MICHAEL from Kennewick, WA
Parts Used:
734-04018C
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
The treads on the front drive wheels were worn down to the point that they provided little traction.
Removed a single nut on each end of the drive shaft with the appropriate socket. Wheels then slipped off. Cleaned/polished the shaft with fine sandpaper, lubed with silicone spray, slid on the wheels and reinstalled the nuts with the same socket. Wheels were an exact fit and OEM quality. Done in 15 minutes start to finish.
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from WAYNE, MI
Parts Used:
734-04018C
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Front drive wheels were wore out
Unbolted old wheels and bolted new wheels to my lawn mower
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jay from GERRY, NY
Parts Used:
734-04018C
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Not the exact fit
I had to drill and tap the ends of the axle and put a 1/4” bolt in to fasten the wheels. The hubs were not the same. They fastened differently.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!