Troy-Bilt Edger Parts

Troy-Bilt Appliance Parts

Popular Troy-Bilt Edger Parts

Tiller Jamlock Nut
$6.51
In Stock
Fix Number
FIX9299545
Manufacturer Part Number
712-0266A
FUEL TANK ASM W/LN
$43.53
Special Order
Fix Number
FIX19283368
Manufacturer Part Number
753-06240
This is an authentic fuel tank assembly for a trimmer. This assembly includes the fuel tank, fuel lines, and a fuel cap. Please note that the tabs used to secure the tank are sold separately. Replacing this fuel tank assembly will solve a leaking fuel tank, deteriorated fuel lines, or a broken fuel cap. If your fuel tank is leaking, this assembly should solve the issue. Never run your equipment with a damaged fuel tank, as this is unsafe. Before making this repair, be sure to drain the gas tank.
Rod-adjust
$24.92
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10007704
Manufacturer Part Number
747-04110A
This is a Manufacturer Approved replacement part designed for Trimmers/Edgers. This blade adjustment rod is made out of Metal and it is Sold Individually. Blade adjustment rod lets you adjust the position of the blade for bevel cutting. When replacing this Rod you will need Pliers, Socket set, Wrench Set.
Bearing
$31.35
In Stock
Fix Number
FIX9167498
Manufacturer Part Number
941-0155
This authentic OEM sourced replacement part is designed for MTD lawn and garden equipment. Ball bearings are generally utilized to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. Unfortunately, over time components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-quality bearing is made of durable metal and is sold individually.
CARBURETOR W/PRIME
$96.65
Special Order
Fix Number
FIX19282841
Manufacturer Part Number
753-05251
This is a genuine OEM sourced replacement part used on gas trimmers/edgers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine wont start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This is a metal body carburetor, it is sold individually. This assembly includes fuel lines, primer bulb. You will need a screwdriver to perform this repair.
Edger Blade
$12.41
In Stock
Fix Number
FIX9129938
Manufacturer Part Number
781-0080-0637
This edger blade is an OEM part direct from Craftsman for edgers. This part connects to the drive shaft to edge and cut grass. It is recommended to review your models diagram to verify the parts compatibility. You will need a wrench to replace this part. This edger blade is made of metal and sold individually.
Snow Blower Star Knob
$11.07
In Stock
Fix Number
FIX9109078
Manufacturer Part Number
720-04072A
This star knob specifically fits a variety of lawn mowers and is used to secure both the lower and upper handles of your lawn mower. If your knob is worn out or loose, then replacing it will solve your problem. No tools are required for this repair. For installation instructions and more information on the part, refer to the manual provided by the manufacturer. This knob is secured with a carriage bolt, which is sold separately. *Please note: this knob is sold separately as well.
SPARK PLUG 4 CYCL
$11.59
On Order
Fix Number
FIX19298356
Manufacturer Part Number
794-00082
FUEL TANK PADS
$10.41
Special Order
Fix Number
FIX19282846
Manufacturer Part Number
753-05259
It is an authentic item that is supplied directly from original equipment manufacturer for use with MTD and Troy-Bilt string trimmer, edgers and backpack blowers. These replacement pads are used to secure the fuel tank. It is made of durable rubber material and it is sold individually.
AIR FILTER
$15.54
Special Order
Fix Number
FIX19312706
Manufacturer Part Number
BS-799579
The pre filter is a genuine replacement part for lawn mowers made by Troy-Bilt, MTD, Yard Machines, and Bolens. A wrench set may be needed during the replacement of this part. It is made out of foam and will need to be replaced if it gets dirty. This item is sold individually and helps to clean the air that enters the carburetor.

Troy-Bilt Edger Appliance Types

Related Troy-Bilt Edger Parts

Popular Troy-Bilt Edger Models