RCA Parts

RCA Appliance Parts

Popular RCA Parts

Fix Number
FIX298977
Manufacturer Part Number
WR2X8345
This genuine OEM part is an end cap for the retainer bar on your fridge or freezer door. The retainer bar is used to keep items secure on the door shelves. The cap can be used for either the left- or right-hand side and is sold individually. A screwdriver may be required to pop open the locking tabs to replace the end caps.
Surface Burner - 8 Inch - 2600W
$34.27
In Stock
Fix Number
FIX11743367
Manufacturer Part Number
WP660533
NOTE: The manufacturer recommends that you replace the burner receptacle at the same time.
Fixes these symptoms

Installation Instructions

sharen from Virgini Beach, VA
surface elements were not working
Just inserted the surface elements into the top of the stove and they heated up and it is working fine. Read more...
Light Bulb - 40W
$21.95
In Stock
Fix Number
FIX217532
Manufacturer Part Number
40A15
This 40-Watt light bulb is sold individually. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place.

Installation Instructions

Jeffrey from SEATTLE, WA
Bake element replacement
1. Turn of over power at the breaker.
2. Remove bake element cover. There's 2 quarter inch nuts.
3. Disconnect old element. For me there was not much play in the wires so when I disconnected the old element I lost the wire in the insulation. If this happened you can remove the central plate cover on the back of the oven and you can easily find the wires again.
4. Connect the replacement element.
5. Screw the bake element cover back in.
6. Turn power back on.
Read more...
Drip Bowl - 8 Inch
$26.19
In Stock
Fix Number
FIX244696
Manufacturer Part Number
WB32X106
Drip bowls are designed to catch any spills or messes from cooking on your stove top. The bowls sit underneath the burner elements on your stove and can easily be removed for cleaning. If your drip bowls have become rusty, damaged, or are just filthy beyond cleaning, they should be replaced. This is a genuine OEM replacement drip bowl that fits under the 8-inch elements and is sold individually. Before replacing this part, please be sure that the element is turned off and cooled down completely. No tools are required to replace the bowls, simply pull out the burner element, remove the old drip bowl, line up the holes on the new bowl, and reinstall the burner element into the terminal.
Fixes these symptoms

Installation Instructions

Catherine from West Warwick, RI
I have a 24" Hotpoint range that needed drip bowls badly.
I had gone to local hardware stores to pick up replacement drip bowls. They specifically stated they were for Hotpoint electric plug-ins, but I was back and forth to the stores trying to find the ones that would fit. I finally ordered through this site. Got them in just a couple of days, and they fit like a charm. It's what I'll do next time to save myself a lot of trouble! Read more...
Fix Number
FIX299562
Manufacturer Part Number
WR2X9144
The end cap is used to hold the retainer bar on the fridge door in place. This genuine OEM part is made of white plastic and can be used for either the left or righthand side of the bar. The retainer bar keeps items from falling off the shelf when the fridge door is open and closed. If an end cap has become damaged, the retainer bar may not stay in place properly. The end caps are sold individually, so if you need to replace more than one, please be sure to order the correct quantity. To replace an end cap, you will need a small flat blade screwdriver to release the locking tabs.

Installation Instructions

marcelino from bronx, NY
Then end cap was broken.
I removed the end caps and put the new ones in by hand. It was a breeze Read more...
Ice Maker
$211.13
In Stock
★★★★★
★★★★★
4 Reviews
Fix Number
FIX1993870
Manufacturer Part Number
WR30X10093
The ice maker assembly makes ice by filling the tray with water from the inlet valve, freezing it until solid cubes are formed, and then ejecting them into the ice bucket. This process will repeat until the bucket has reached capacity. If your fridge is no longer making ice, the assembly may need to be replaced. This is a genuine OEM replacement that measures 10 inches by 5 inches in size and will make seven crescent shaped pieces of ice each cycle. The kit is mainly made of white plastic, and includes a 4-pin round plug-in connector, a 6-post plug-in connector, tube, and fill cup. Depending on your frequency of use, the ice maker may need to be replaced every three to ten years. Regular wear and tear is the main reason this part may need to be replaced but be mindful of accidental damage.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...

Installation Instructions

marion from raleigh, NC
Ice maker stopped making ice
Super easy. Loosen 2 screws. Disconnect power line. Take out broken part and plug in new part then slide icemaker back in place and tighten 2 screws. Saved me the $89 service call plus whatever they would have overcharged for the part! And no waiting around for repair guy! Read more...
Fix Number
FIX2359946
Manufacturer Part Number
WR24X10231
This white rubber door gasket creates an airtight seal for the refrigerator door, helping maintain temperature and energy efficiency. It replaces worn or damaged seals that cause leaks, condensation, or cooling issues. Genuine OEM part; replace if torn or loose.
Fixes these symptoms
  • Door Sweating
  • Door won’t open or close
  • Fridge runs too long
  • See more...
Drip Bowl - 6 Inch
$21.82
In Stock
Fix Number
FIX244697
Manufacturer Part Number
WB32X107
This genuine OEM part is a 6-inch chrome drip bowl. The drip bowl fits under the coiled burner elements on your electric range and is used to collect drips and spills that happen while cooking. If the drip bowls have become damaged, rusty, or are missing entirely, they should be replaced. If you need to replace more than one drip bowl, please be sure to order the appropriate quantity as this part is sold individually. No tools are required to replace the part, but please ensure that the burners are turned off and completely cool to the touch before starting this repair.

Installation Instructions

Catherine from West Warwick, RI
I have a 24" Hotpoint range that needed drip bowls badly.
I had gone to local hardware stores to pick up replacement drip bowls. They specifically stated they were for Hotpoint electric plug-ins, but I was back and forth to the stores trying to find the ones that would fit. I finally ordered through this site. Got them in just a couple of days, and they fit like a charm. It's what I'll do next time to save myself a lot of trouble! Read more...
★★★★★
★★★★★
1 Review
Fix Number
FIX267529
Manufacturer Part Number
WE25M40
This rear drum bearing kit is a genuine OEM replacement for your dryer. The kit includes a shaft, ground strap, bracket, bearing and seven screws for installation. The bearing supports that back of the dryer drum and helps to reduce friction so that the drum can rotate smoothly and quietly. If the bearing has worn out, it can result in your dryer not tumbling, or making excessive noise when it is running.
Fixes these symptoms

Installation Instructions

Stephen from Bridgewater, NJ
noisy
New shaft, belt and housing. Installation was going fine until went to install belt and IT was way to short .THANKS Read more...
LIGHT SWITCH
$36.42
In Stock
Fix Number
FIX16554876
Manufacturer Part Number
WR23X37285
The light switch in your refrigerator is used to turn the light on and off when the fridge door opens or closes. This is considered a closed switch, which means that when the fridge door depresses the button there is no continuity and the light turns off. When the fridge door opens and the button is released, there is continuity, and the light turns on. If the light in your fridge is not burned out but will not come on, the switch may need to be replaced. This genuine OEM replacement light switch is spring loaded and made of a white plastic. This is an easy repair that will require a flat blade screwdriver and a pair of needle nose pliers to complete the job. Since you will be working with electrical components, please be sure to disconnect the power supply to your fridge before beginning this repair.
Fixes these symptoms

Installation Instructions

Sheila from los angeles, CA
Door would not close after insatallation
Followed the video with no problems, but the door would not close. There is a rubber bumper that the light switch strikes, This bumper was not horizontal, and just had to be twisted to a horizontal position. The door then closed tightly, Total repair time was about 5 minutes! Read more...

RCA Appliance Types

Popular RCA Models