Scroll Saw Parts

Brush

$10.63

Fix Number: FIX10168838
Manufacturer Part Number: 286346-00

Genuine DeWalt replacement part Includes 1 Carbon Brush with wire lead and brush spring attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. • Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. • A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. • When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Table Insert

$6.25

Fix Number: FIX10326926
Manufacturer Part Number: 900200

This replacement table insert is specially designed for Delta scroll saws. It is a genuine part that is supplied from original equipment manufacturer. The purpose of an insert is to reduce the splintering and chips on the cuts. It also helps to prevent thin slices of wood from jamming in between the blade and the plate. This item is made out of plastic and it is sold individually. To replace this table insert no tools would be needed. Simply place it in the slot on the table/bench.

Fuse,3a

$11.48

Fix Number: FIX10168837
Manufacturer Part Number: 286344-00

This fuse is a high quality part sourced from the original manufacturer for DeWalt and Delta scroll saws. The fuse is a safety feature to prevent an electric surge from overloading the motor. Once the fuse is tripped it will burn itself out, and will need to be replaced. This part is sold individually, keep in mind the fuse cap is sold separately.

Watch the install video

Clamp Knob Assembly

$24.56

Fix Number: FIX10168807
Manufacturer Part Number: 286303-00

This is a single OEM clamp knob assembly for a saw. The clamp knob is what secures the blade in the saw blade clamp. This assembly has a wingnut cast onto a threaded metal stud. With use, the clamping surface will deteriorate, which causes the blade to slip. The threads on the metal stud can also start to strip. For this quick and easy repair, you will need to disconnect the blade, and then unscrew and remove the clamp knob from the blade chuck. To install your new part, fasten the clamp knob into the blade chuck and reassemble the blade.

Bar

$16.63

Fix Number: FIX10168798
Manufacturer Part Number: 286291-00

This is a genuine OEM sourced replacement part that is intended to be used with scroll saws from DeWalt and Delta. The metal bar attaches to the top rocker mount and is used to support the foot that protects the blade. The bar will require a torx driver and hex driver to install, and the bar is priced as a single item.

Bellows

$6.25

Fix Number: FIX10168796
Manufacturer Part Number: 286289-00

This is an authentic replacement part, sourced from the original manufacturer for use with scroll saws. The special rubber bellow is used to push air through the air pump and through the air nozzle. This bellow is available as an individual replacement part, please see model diagram for associative parts.

Watch the install video

Switch

$38.42

Fix Number: FIX10177981
Manufacturer Part Number: 5140092-86

This is an OEM replacement part used in Delta and DeWALT scroll saws. It is an on/off switch and is sold individually, separate from the speed control knob. It is plastic with metal terminals. Over time, mechanical parts such as these wear down and must be replaced. To complete this repair you will need a hex key/allen wrench. • Remove old switch by pressing tabs • Disconnect wires • Attach wires to the new switch • Reassemble and test the tool

Foot

$14.98

Fix Number: FIX10168799
Manufacturer Part Number: 286292-00

This part is guaranteed OEM, made to fit the DeWALT and Delta scroll saws listed below. This hold down foot is attached to the top mount via the black bar. Note that mounting/adjustment screw is sold separately. This foot is sold individually. Associated parts: • Top Mount, part # 286277-00 • Bar, part # 286291-00 • Screw, part # 286316-00

Watch the install video

Air Nozzle

$25.16

Fix Number: FIX10168812
Manufacturer Part Number: 286311-00

This is an authentic OEM replacement part, guaranteed to fit the scroll saws listed below. This adjustable air nozzle/hose is used as a dust blower. It is connected to the bellows via the metal air pump cap. Nozzle attaches over the air pump cap's ball end. When installing this part it is recommended to heat the nozzle's connecting end until soft. Then just ease into place. This item is sold individually. A Torx screwdriver is used to remove the air pump cap for easier installation.

Installation Instructions

Chuck from GREER, SC

The blower nozzle had cracked and would not stay in place.

The replacement should be an easy push on operation but the end joint needs to heated to fit over the outlet ball. Dip the end of the plastic joint in boiling water for about 30 seconds and immediately press over the fitting. Installation is complete. Read more...

Band Saw Table Insert

$13.20

★★★★★

2 Reviews

Fix Number: FIX10323790
Manufacturer Part Number: 426020630001S

This is a table insert plate for your saw. It is attached to the table, and provides access to the blade. A table insert protects the rest of the unit by preventing wood from getting jammed under the blade during cutting. The slit in the insert plate allows for the saw blade to run smoothly. Before installing this part, unplug your saw.

Popular Scroll Saw Parts

Installation Instructions

Scroll Saw Brands

Related Scroll Saw Parts

Popular Scroll Saw Models

Scroll Saw Parts

Start With Your Model Number

Popular Scroll Saw Parts

Installation Instructions

Scroll Saw Brands

Related Scroll Saw Parts

Popular Scroll Saw Models